FMI CD36M-LS Скачать руководство пользователя

Страница: 25 / 40

www.fmiproducts.com

125205-01E

Figure 48 - Control Knob in Pilot Position

Position

Indicator

Gas Control

Knob

HI/LO Knob

D. Do not use this appliance if any part has

been under water. Immediately call a

qualified service technician to inspect

the appliance and to replace any part of

the control system and any gas control

which has been under water.

LIGHTING

INSTRUCTIONS

1. STOP! Read safety information in column

1 before proceeding.

2. Turn off all electrical power to appliance.

3. Open bottom access louver.

4. Slide remote selector to OFF position.

5. Make sure manual shutoff valve is fully open.

6. Push in gas control knob slightly and turn

clockwise

to OFF.

7. Wait five (5) minutes to clear out any gas.

Then smell for gas, including near floor. If

you smell gas, STOP! Follow B in safety

information in column 1. If you don’t smell

gas, go to next step.

8. Visually locate pilot assembly by main burner.

9. Turn knob on gas control counterclock-

wise

to PILOT.

10. Push control knob all the way in and hold.

Immediately light pilot by pressing red ig-

nitor button until flame appears. Continue

to hold control knob in for about one (1)

minute after pilot is lit. Release knob and

it will pop back up. Pilot should remain lit.

If it goes out, repeat steps 6 through 10.

• If knob does not pop out when released,

stop and call service technician or gas

supplier.

• If pilot will not stay lit after several tries,

turn gas control knob to OFF and call

your service technician or gas supplier.

11. Turn gas control knob counterclockwise

to ON. Knob can be turned to ON

only if control knob is popped out.

12. Set HI-LO knob to desired setting.

13. Slide remote sector switch to REMOTE

position to operate using remote control.

Selector switch must be in the ON position

to operate manually.

OPERATION

Continued

14. Turn on all electric power to appliance.

Note: It is recommended that you maintain

gas control knob in the full OFF position during

lengthy periods of seasonal non use.

Figure 49 - Pilot

Thermocouple

Pilot Burner

Piezo Ignitor

Thermopile

TO TURN OFF GAS

TO APPLIANCE

1. Turn off wall switch, if installed.
2. Turn off all electric power to appliance if

service is to be performed.

3.  Open bottom access louver.
4.  Slide selector switch to OFF position.
5.  Push in gas control knob slightly and turn

clockwise

to OFF. Do not force.

6. Close bottom access louver.

OPTIONAL HAND-HELD

REMOTE OPERATION

Note: All remote control accessories must be pur-

chased separately (see Accessories, page 38).

Follow instructions included with remote control.

NOTICE: You must light the pilot

before using the hand-held re

mote control unit. See

Lighting

Instructions

After lighting, let pilot flame burn for about

one minute. Turn control knob to ON posi-

tion. Adjust flame adjustment knob anywhere

between HI and LO. Slide selector switch to

the REMOTE position.

Note: The burner may light if hand-held re-

mote was on when selector switch was last

turned off. You can now turn burner on and off

with hand-held remote control unit.

IMPORTANT:

Do not leave the selector switch

in the REMOTE or ON position when the pilot

is not lit. This will drain the battery.

Содержание CD36M-LS









































Результаты поиска

Содержание CD36M-LS

Отзывы:

Похожие инструкции для CD36M-LS

Бренды по названию

Популярные бренды

FMI CD36M-LS, Руководство владельца по эксплуатации и установке

Результаты поиска

Содержание CD36M-LS

Отзывы:

Похожие инструкции для CD36M-LS

Бренды по названию

Популярные бренды