FMI CD36M-LS Скачать руководство пользователя

Страница: 22 / 40

www.fmiproducts.com

125205-01E

INSTALLATION

Continued

INSTALLING BLOWER ACCESSORY

NOTICE: If installing blower in

an existing fireplace with gas

connections, shut off gas supply

and disconnect fireplace from

gas supply. Contact a qualified

service person to do this.

WARNING: If there is a duplex

electrical outlet installed in the

right side of the bottom of the

fireplace base area, be sure that

the electrical power to the outlet is

turned off before proceeding with

blower installation. Failure to do

this may result in serious injury.

Model BK Installation

Follow all instructions provided in blower

accessory kit.
1. Attach power cord to blower motor by

firmly pushing two female terminals at end

of power cord onto two spade terminals

on blower motor (see Figure 41).

2. Attach green ground wire from power cord

to blower housing using screw provided

(see Figure 41). Tighten screws securely.

3. Place blower against lower rear wall of

firebox outer wrapper with exhaust port

directed upward. Blower will fit inside back

opening and be held in position against back

wall by magnets (see Figure 41).

4. Be certain that all wire terminals are

securely attached to terminals on blower

motor and that screw retaining green

ground wire is tight.

5. Mount speed control box to switch bracket

by placing plastic control shaft forward

through round opening in switch bracket

(see Figure 42).

6. While supporting speed control, secure

control shaft with lock nut by pushing

and turning lock nut with pliers clockwise

until it is tight against front panel. Place

provided control knob on shaft.

7. Turn on power to duplex outlet if previously

turned off per warning in this column.

8. Plug in blower power cord.

a. If your firebox is installed as a free

standing unit with an accessory mantel,

determine whether power cord will exit

left side or right side of firebox. Route

power cord through exit hole and plug

power cord into a wall receptacle near

firebox.

b. If your firebox installation is recessed

and/or pre-wired, plug power cord into

duplex outlet provided. Refer to your

firebox owner’s manual for instructions

on wiring duplex outlet.

Blower Location

Side View

Figure 41 - Blower Model BK

Magnetic

Strips

Exhaust Port

Screw

Spade

Terminals

Lower Firebox

Cavity

Figure 42 - Attaching Speed Control to

Firebox

Speed Control Control Shaft

Locknut

Switch

Bracket

Blower

Plug-In

Duplex Outlet (Located

beneath firebox floor

against lower right

outside wall)

CAUTION: Never touch the

blower wheel while in operation.

Содержание CD36M-LS









































Результаты поиска

Содержание CD36M-LS

Отзывы:

Похожие инструкции для CD36M-LS

Бренды по названию

Популярные бренды

FMI CD36M-LS, Руководство владельца по эксплуатации и установке

Результаты поиска

Содержание CD36M-LS

Отзывы:

Похожие инструкции для CD36M-LS

Бренды по названию

Популярные бренды