FMI CD36M-LS Скачать руководство пользователя

Страница: 27 / 40

www.fmiproducts.com

125205-01E

GAS CONVERSION

Continued

Figure 52 - Installing New Parts for Gas

Control Valve Conversion

FF P

Mounting

Screws

Rubber

Gasket

Identification

Label

WARNING: The conversion

kit must be installed by a quali

fied service technician in accor

dance with the manufacturers

instructions and all applicable

codes and requirements of the

authority having jurisdiction. If

any information is these instruc-

tions is not followed correctly,

a fire, explosion or production

of carbon monoxide may result

causing property damage, per

sonal injury or loss of life. The

qualified service technician is

responsible for the proper in

stallation of this conversion kit.

2. Insure that rubber gasket is properly

positioned on new pressure regulator

assembly. Install new pressure regulator

assembly to valve using new mounting

screws supplied with kit. Tighten screws

securely (approximately 25 in/lb). See

Figure 52.

3. Install identification label enclosed with

gas valve regulator to valve body where

it can easily be seen (see Figure 52).

CLEANING AND

MAINTENANCE

WARNING: Turn off fireplace

and let cool before cleaning.

CAUTION: You must keep

control areas, burners and

circulating air passageways of

fireplace clean. Inspect these

areas of fireplace before each

use. Have fireplace inspected

yearly by a qualified service

person. Fireplace may need

more frequent cleaning due to

excessive lint from carpeting,

bedding material, pet hair, etc.

GLASS DOOR

WARNING: Handle glass

door panel with care. Do not

strike, slam or otherwise abuse

glass. Do not operate fireplace

with the glass door unlatched,

removed, cracked or broken.

WARNING: Do not use

abrasive cleaners as this may

damage glass. Use a nonabra

sive household glass cleaner to

clean glass. Do not clean glass

when hot.

Glass must be cleaned periodically. During

start-up it is normal for condensation to form

on the inside of the glass causing lint, dust

and other airborne particles to cling to the

glass surface. During initial start-up a slight

film may form on the glass due to paint curing.

The glass should be cleaned several times

with a non-ammonia, nonabrasive household

cleaner and warm water after the first two

weeks of operation. Thereafter, clean the

glass two or three times during each heat-

ing season, depending on the usage and

circumstances present. Refer to

Removing

Glass Panel

, page 18 of this manual when

removing glass door for cleaning.

Содержание CD36M-LS









































Результаты поиска

Содержание CD36M-LS

Отзывы:

Похожие инструкции для CD36M-LS

Бренды по названию

Популярные бренды

FMI CD36M-LS, Руководство владельца по эксплуатации и установке

Результаты поиска

Содержание CD36M-LS

Отзывы:

Похожие инструкции для CD36M-LS

Бренды по названию

Популярные бренды