FMI CD36M-LS Скачать руководство пользователя

Страница: 10 / 40

www.fmiproducts.com

125205-01E

INSTALLATION

WARNING: This gas fireplace

and vent assembly must be

vented directly to the outside. The

venting system must NEVER be

attached to a chimney serving a

separate solid fuel burning appli

ance. Each gas appliance must

use a separate vent system. Do

not use common vent systems.

WARNING: Horizontal sec-

tions of this vent system require

a minimum clearance of 2" from

the top of the pipe and 1" mini

mum to the sides and bottom.

Vertical sections of this system

require a minimum of 1" clear

ance to combustible materials

on all sides of the pipe.

VENTING INSTALLATION

1. Install elbow to fireplace collar adapter

located on back of the unit at a 45° angle.

Slide elbow over collar and twist to lock.

Check to insure proper connection (see

Figure 6).

2. Continue to install remainder of pipe for

desired installation. Make sure each sec-

tion is twist-locked securely.

3. When installation of vent pipe is complete,

in stall vent termination. Depending on

location of your fireplace, you will vent

vertically or horizontally.

4. Allow 1" of pipe to protrude from internal

wall, depending on wall thickness. See

Figure 7, page 11.

Figure 6 - Venting Installation

Female

Locking

Lugs

Male

Locking Lugs

Vertical Flue

Restrictor

(For Vertical

Venting

Application)

WARNING: Read all instruc-

tions completely and thoroughly

before attempting installation.

Failure to do so could result in

serious injury, property dam

age or loss of life. Operation of

improperly installed and main

tained venting system could

result in serious injury, property

damage or loss of life.

NOTICE: Failure to follow these in-

structions will void the warranty.

VENTING INSTALLATION

PRECAUTIONS

Consult local building codes before beginning

installation. Installer must make sure to select

proper vent system for installation. Before

installing vent kit, installer must read this fire

place manual and vent kit instructions.

Only a qualified service person should install

venting system. The installer must follow

these safety rules:

• Wear gloves and safety glasses for

protection

• Use extreme caution when using ladders

or when on roof tops

• Be aware of electrical wiring locations in

walls and ceilings

The following actions will void the warranty

on your venting system:

• Installation of any damaged venting compo

nent

• Unauthorized modification of the venting

system

• Installation of any component part not

manufactured or approved for use with the

fireplace.

• Installation other than as instructed by

these instructions

NOTICE: All FMI PRODUCTS,

LLC direct vent fireplaces only

approved 5/8" pipe components

and terminations.

Содержание CD36M-LS









































Результаты поиска

Содержание CD36M-LS

Отзывы:

Похожие инструкции для CD36M-LS

Бренды по названию

Популярные бренды

FMI CD36M-LS, Руководство владельца по эксплуатации и установке

Результаты поиска

Содержание CD36M-LS

Отзывы:

Похожие инструкции для CD36M-LS

Бренды по названию

Популярные бренды