background image

125204-01

Rev. C

04/13

WARRANTY

KEEP THIS WARRANTY

FMI PRODUCTS, LLC LIMITED WARRANTIES

New Products

Standard Warranty:

 FMI PRODUCTS, LLC warrants this new product and any parts thereof to be free from defects 

in material and workmanship for a period of two (2) years from the date of first purchase from an authorized dealer 

provided the product has been installed, maintained and operated in accordance with FMI PRODUCTS, LLC’s 

warnings and instructions.
For products purchased for commercial, industrial or rental usage, this warranty is limited to 90 days from the date 

of first purchase.

Factory Reconditioned Products

Limited Warranty:

 FMI PRODUCTS, LLC warrants factory reconditioned products and any parts thereof to be 

free from defects in material and workmanship for 30 days from the date of first purchase from an authorized dealer 

provided the product has been installed, maintained and operated in accordance with FMI PRODUCTS, LLC’s 

warnings and instructions.

Terms Common to All Warranties

The following terms apply to all of the above warranties:
Always specify model number and serial number when contacting the manufacturer. To make a claim under this 

warranty the bill of sale or other proof of purchase must be presented.

This warranty is extended only to the original retail purchaser when purchased from an authorized dealer, and only 

when installed by a qualified installer in accordance with all local codes and instructions furnished with this product.

This warranty covers the cost of part(s) required to restore this product to proper operating condition and an allowance 

for labor when provided by a FMI PRODUCTS, LLC Authorized Service Center or a provider approved by FMI PROD

-

UCTS, LLC. Warranty parts must be obtained through authorized dealers of this product and/or FMI PRODUCTS, LLC 

who will provide original factory replacement parts. Failure to use original factory replacement parts voids this warranty.
Travel, handling, transportation, diagnostic, material, labor and incidental costs associated with warranty repairs, unless 

expressly covered by this warranty, are not reimbursable under this warranty and are the responsibility of the owner.

All warranty will be voided if this product is used with a thermostat.
Excluded from this warranty are products or parts that fail or become damaged due to misuse, accidents, improper 

installation, lack of proper maintenance, tampering, or alteration(s).

This is FMI PRODUCTS, LLC’s exclusive warranty, and to the full extent allowed by law; this express warranty 

excludes any and all other warranties, express or implied, written or verbal and limits the duration of any and all 

implied warranties, including warranties of merchantability and fitness for a particular purpose to two (2) years on 

new products and 30 days on factory reconditioned products from the date of first purchase. FMI PRODUCTS, LLC 

makes no other warranties regarding this product.
FMI PRODUCTS, LLC’s liability is limited to the purchase price of the product, and FMI PRODUCTS, LLC shall not 

be liable for any other damages whatsoever under any circumstances including indirect, incidental, or consequential 

damages.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental 

or consequential damages, so the above limitation or exclusion may not apply to you. 

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. 

For information about this warranty contact:

Model (

located on product or identification tag

) _____________________________

Serial No. (

located on product or identification tag

) __________________________

Date Purchased  __________________________

Keep receipt for warranty verification.

2701 S. Harbor Blvd.

Santa Ana, CA 92704

1-866-328-4537

www.fmiproducts.com

f i r e - p a r t s . c o m

Содержание CD32M-LS

































Отзывы: