FLYGT 3126.290 Скачать руководство пользователя | Manualshive

Страница: 6 / 48

background image

Hazard level

Indication

WARNING:

A hazardous situation which, if not avoided, could result

in death or serious injury

CAUTION:

A hazardous situation which, if not avoided, could result

in minor or moderate injury

NOTICE:

• A potential situation which, if not avoided, could

result in undesirable conditions

• A practice not related to personal injury

Hazard categories

Hazard categories can either fall under hazard levels or let specific symbols replace the
ordinary hazard level symbols.
Electrical hazards are indicated by the following specific symbol:

Electrical Hazard:

These are examples of other categories that can occur. They fall under the ordinary
hazard levels and may use complementing symbols:

• Crush hazard
• Cutting hazard
• Arc flash hazard

Environmental safety

The work area

Always keep the station clean.

Waste and emissions regulations

Observe these safety regulations regarding waste and emissions:

• Appropriately dispose of all waste.
• Handle and dispose of the processed liquid in compliance with applicable

environmental regulations.

• Clean up all spills in accordance with safety and environmental procedures.
• Report all environmental emissions to the appropriate authorities.

CAUTION: Radiation Hazard

Do NOT send the product to Xylem if it has been exposed to nuclear radiation, unless
Xylem has been informed and appropriate actions have been agreed upon.

Electrical installation

For electrical installation recycling requirements, consult your local electric utility.

Recycling guidelines

Always recycle according to these guidelines:

Introduction and Safety

4

Flygt 3126.290 Installation, Operation, and Maintenance Manual

«
...
4
5
6
7
8
...
»

Содержание 3126.290

















































Отзывы:

Нет отзывов

Похожие инструкции для 3126.290

Бренд: Haier Страницы: 2

Бренд: Nastec Страницы: 28

Бренд: XPOtool Страницы: 10

PROTÉGÉ RPAGP

Бренд: Raypak Страницы: 3

Бренд: Honda Страницы: 75

Бренд: Ultranatura Страницы: 24

Бренд: Binks Страницы: 40

Бренд: Lochinvar Страницы: 1

Бренд: Oase Страницы: 179

Бренд: Emec Страницы: 44

Бренд: Watson-Marlow Страницы: 138

Бренд: ACPro Страницы: 24

Бренд: Rapid Страницы: 12

GE50T BQT Series

Бренд: GE Страницы: 68

GARLAND GEISER 391 XE

Бренд: Glasswelt Страницы: 84

Бренд: STIEBEL ELTRON Страницы: 16

Бренд: Hypertherm Страницы: 194

Бренд: Gude Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды