manualshive.com logo in svg

FLYGT 3126.290, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
FLYGT 3126.290 Скачать руководство пользователя страница 7

1. Follow local laws and regulations regarding recycling if the unit or parts are accepted

by an authorized recycling company.

2. If the first guideline is not applicable, then return the unit or parts to your local sales

and service representative.

User safety

General safety rules

These safety rules apply:

• Always keep the work area clean.
• Pay attention to the risks presented by gas and vapors in the work area.
• Avoid all electrical dangers. Pay attention to the risks of electric shock or arc flash

hazards.

• Always bear in mind the risk of drowning, electrical accidents, and burn injuries.

Safety equipment

Use safety equipment according to the company regulations. Use this safety equipment
within the work area:

• Hard hat
• Safety goggles, preferably with side shields
• Protective shoes
• Protective gloves
• Gas mask
• Hearing protection
• First-aid kit
• Safety devices

NOTICE:

Never operate a unit unless safety devices are installed. Also see specific information
about safety devices in other chapters of this manual.

Electrical connections

Electrical connections must be made by certified electricians in compliance with all
international, national, state, and local regulations. For more information about
requirements, see sections dealing specifically with electrical connections.

Hazardous liquids

The product is designed for use in liquids that can be hazardous to your health. Observe
these rules when you work with the product:

• Make sure that all personnel who work with biologically hazardous liquids are

vaccinated against diseases to which they may be exposed.

• Observe strict personal cleanliness.

Wash the skin and eyes

Follow these procedures for chemicals or hazardous fluids that have come into
contact with your eyes or your skin:

Condition

Action

Chemicals or hazardous fluids in

eyes

1. Hold your eyelids apart forcibly with your fingers.
2. Rinse the eyes with eyewash or running water for at least 15 minutes.
3. Seek medical attention.

Introduction and Safety

Flygt 3126.290 Installation, Operation, and Maintenance Manual

5

Содержание 3126.290

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды