FLYGT 3126.290 Скачать руководство пользователя

Страница: 36 / 48

Service item

Action

Impeller

1. Check the impeller clearance.
2. Adjust the impeller, if necessary.

Stator housing

1. Drain all liquid, if any.
2. Check the resistance of the leakage sensor.

Normal value approximately1500 ohms, alarm approximately

430 ohms.

Insulation

Use a megger maximum 1000 V.
1. Check that the resistance between the ground (earth) and phase

lead is more than 5 megaohms.

2. Conduct a phase-to-phase resistance check.

Junction box

Check that it is clean and dry.

Lifting device

Check that local safety regulations are followed.

Lifting handle

1. Check the screws.
2. Check the condition of the lifting handle.
3. Replace if necessary.

O-rings

1. Replace the oil plug O-rings.
2. Replace the O-rings at the entrance or junction cover.
3. Grease the new O-rings.

Overload protection and other

protections

Check the correct settings.

Personnel safety devices

Check the guard rails, covers, and other protections.

Rotation direction

Check the impeller rotation.

Oil housing

Fill with new oil, if necessary.

Terminal block/closed end splice

Check that the connections are properly tightened.

Thermal contacts

Normally closed circuit; interval 0–1 ohm.

Voltage and amperage

Check the running values.

Major overhaul

For a major overhaul, do the following in addition to the tasks listed under Inspection.

Service item

Action

Support and main bearing

Replace the bearings with new bearings.

Mechanical seal

Replace with new seal units.

Service in case of alarm

For information about indication values for sensors, see

Sensors connection

Alarm source

Action

FLS

1. Check for liquid in the stator housing.
2. Drain all liquid, if any.
3. Check the mechanical seal unit, the O-rings, and the cable entry, if

liquid was found.

Thermal contact

Check the start and stop levels.
Check that the cooling jacket is not clogged. Clean if necessary.
1. Check the coolant level (pump with cooling jacket).
2. Check the start and stop levels.

Replace the impeller

Required tools:

Maintenance

Flygt 3126.290 Installation, Operation, and Maintenance Manual

Содержание 3126.290

















































Результаты поиска

Содержание 3126.290

Отзывы:

Похожие инструкции для 3126.290

Бренды по названию

Популярные бренды

FLYGT 3126.290, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание 3126.290

Отзывы:

Похожие инструкции для 3126.290

Бренды по названию

Популярные бренды