manualshive.com logo in svg

FLYGT 3126.290, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
FLYGT 3126.290 Скачать руководство пользователя страница 22

WS008385A

Figure 4: T-installation

These items are required:

• Anchor bolts for anchoring the pump to a base.
• Shut-off valves that allow you to remove the pump from service

NOTICE:

The risk of freezing is particularly high in T- or Z-installations.

1. Fasten the pump:

a) Bolt the stationary suction connection to the concrete base.
b) Bolt the pump to the suction connection.

2. Make sure that the pump is vertical.
3. Connect the suction line and discharge line.
4. Connect the motor cable and the starter and monitoring equipment according to the

separate instructions.
Make sure that the impeller rotation is correct. For more information, see 

Check the

impeller rotation

 (page 27)

5. Make sure that the weight of the pump does not put strain on the piping.

Make the electrical connections

General precautions

DANGER: Electrical Hazard

Before starting work on the unit, make sure that the unit and the control panel are isolated
from the power supply and cannot be energized. This applies to the control circuit as well.

WARNING: Electrical Hazard

Risk of electrical shock or burn. A certified electrician must supervise all electrical work.
Comply with all local codes and regulations.

Installation

20

Flygt 3126.290 Installation, Operation, and Maintenance Manual

Содержание 3126.290

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды