FLYGT 3126.290 Скачать руководство пользователя

Страница: 34 / 48

Screws and nuts

Table 1: Stainless steel, A2 and A4, torque Nm (ft-lbs)

Property

class

M10

M12

M16

M20

M24

M30

1.0 (0.74)

2.0 (1.5)

3.0 (2.2)

8.0 (5.9)

15 (11)

27 (20)

65 (48)

127 (93.7) 220 (162) 434 (320)

70, 80

2.7 (2)

5.4 (4)

9.0 (6.6)

22 (16)

44 (32)

76 (56)

187 (138) 364 (268) 629 (464) 1240 (915)

100

4.1 (3)

8.1 (6)

14 (10)

34 (25)

66 (49)

115 (84.8) 248 (183) 481 (355) —

—

Table 2: Steel, torque Nm (ft-lbs)

Property

class

M10

M12

M16

M20

M24

M30

8.8

2.9 (2.1)

5.7 (4.2)

9.8 (7.2)

24 (18)

47 (35)

81(60)

194 (143) 385 (285) 665 (490) 1310

(966.2)

10.9

4.0 (2.9)

8.1 (6)

14 (10)

33 (24)

65 (48)

114 (84)

277 (204) 541 (399) 935 (689) 1840

(1357)

12.9

4.9 (3.6)

9.7 (7.2)

17 (13)

40 (30)

79 (58)

136 (100) 333 (245) 649 (480) 1120

(825.1)

2210

(1630)

Hexagon screws with countersunk heads

For hexagon socket head screws with countersunk head, maximum torque for all property
classes must be 80% of the values for property class 8.8 above.

Change the oil

The following items are needed for this procedure:

• New oil plugs
• New O-rings
• Oil that should be a medical white oil of paraffin type that fulfills FDA 172.878 (a) and

viscosity close to VG32.

1. Place the pump in a horizontal position.
2. Turn the pump so that the oil hole faces downwards.
3. Unscrew the oil plug.

If the pump has a hole with the markings "oil out" it is important that this hole is used
for drainage.

CAUTION: Compressed Gas Hazard

Air inside the chamber may cause parts or liquid to be propelled with
force. Be careful when opening. Hold a rag over the plug to prevent
liquid from spraying out.

WS001519A

Maintenance

Flygt 3126.290 Installation, Operation, and Maintenance Manual

Содержание 3126.290

















































Результаты поиска

Содержание 3126.290

Отзывы:

Похожие инструкции для 3126.290

Бренды по названию

Популярные бренды

FLYGT 3126.290, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание 3126.290

Отзывы:

Похожие инструкции для 3126.290

Бренды по названию

Популярные бренды