FLYGT 3126.290 Скачать руководство пользователя | Manualshive

Страница: 37 / 48

background image

• 10 mm hexagon bit adapter with an extension of at least 125 mm (4.92 in.)
• Impeller puller

If applicable, contact your local sales and service representative for correct type and
size.

• Two crowbars, if applicable

CAUTION: Cutting Hazard

Worn parts can have sharp edges. Wear protective clothing.

NOTICE:

When laying the pump on its side, do not allow the weight of the pump to rest on any
portion of the impeller. The impeller must not be allowed to make contact with the
concrete floor or other hard and rough surfaces.

If you fail with the impeller installation, then you must redo the installation procedure from
the beginning.

Replace the C- or D-impeller

WS003639A

Figure 10: C-impeller

WS003640A

Figure 11: D-impeller

Remove the impeller: C, D

CAUTION: Cutting Hazard

Worn parts can have sharp edges. Wear protective clothing.

1. Remove the pump housing or the suction cover.

2. Remove the impeller screw.

If applicable, use the rod.

Maintenance

Flygt 3126.290 Installation, Operation, and Maintenance Manual

35

«
...
35
36
37
38
39
...
»

Содержание 3126.290

















































Отзывы:

Нет отзывов

Похожие инструкции для 3126.290

Бренд: Makita Страницы: 24

Бренд: Paloma Страницы: 24

Бренд: Immergas Страницы: 40

MAG HK 13-2/0-3 H

Бренд: Vaillant Страницы: 12

BC-F20HWR2-200L

Бренд: enertik Страницы: 33

Бренд: salmson Страницы: 195

Бренд: esotec Страницы: 3

Бренд: Yardworks Страницы: 19

HOF14AFRQ 1F Series

Бренд: Halsey Taylor Страницы: 4

Бренд: Western Shelter Systems Страницы: 2

Бренд: Pro-Craft Страницы: 24

F 550 GS Series

Бренд: Flux Страницы: 116

Бренд: Parkside Страницы: 122

Бренд: Gorenje Страницы: 64

Бренд: Robuschi Страницы: 21

Бренд: ITS Telecom Страницы: 20

Бренд: F.F. Group Страницы: 28

Бренд: Malmbergs Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды