background image

User Manual 

E110-P

Page 18

FW_E110-P_M_v0301-01_EN

5.2.1

CONFIGURING USING PC CONFIGURATION TOOL

Configuration of the E110-P can be done using a PC with our free of charge Remote Configuration
Tool software. Consult 

Section D: Remote Configuration Tool [»68]

 for details. Connection to a PC is

made by means of the communication port, located at the back side of the MEM.

CONFIG

Fig. 14: 

USB connection between MEM and PC

All settings available in the PC Configuration tool correspond with menu items available in SETUP-
mode. Please see 

Section 5.5: SETUP menu explanations [»23]

.

5.2.2

MECHANICAL KEYS

A quick and convenient way to configure the E110-P is by means of SETUP-mode and three
mechanical keys (push buttons) at the side of the MEM (available with the cover removed).

PROG

CLEAR

SELECT

Fig. 15: 

Control panel pushbuttons

The mechanical keys copy the functionality of the corresponding optical keys at the front side of the
MEM. After operating the mechanical keys, the optical keys are disabled for 30 seconds to avoid
interference and to allow to replace the cover. The Key lock symbol 

 indicates that the optical

keys are temporarily disabled, see 

Section 4.2.2: Optical keys [»10]

.

5.2.3

OPTICAL KEYS SWITCH

The optical keys can be disabled to save battery power or to avoid false activation under some
circumstances. The switch can be found at the outside rim of the MEM. 
The Key lock symbol 

 is shown on the display when the optical keys are disabled, see

Section 4.2.2: Optical keys [»10]

. The mechanical keys always remain active.

Содержание E110-P









































































Отзывы: