Flexim FLUXUS G800 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 161

background image

7 Installation of FLUXUS G801

UMFLUXUS_G8V4-6-1EN, 2018-10-10

39

7

Installation of FLUXUS G801

7.1

Location

• Select the measuring point according to the recommendations in chapter 3 and 5.
• Select the location of the transmitter within the range of the cable of the measuring point.
The ambient temperature at the location has to be within the operating temperature range of the transmitter and the trans-
ducers (see Technical Specification).
If the measuring point is within an explosive atmosphere, the danger zone and gases that may be present have to be de-
termined. The transducers and the transmitter have to be appropriate for these conditions.

7.2

Opening and Closing the Housing

The transmitter has a countersunk screw which has to be unscrewed before the housing can be opened.
After the installation, make sure that the housing is closed correctly and that the countersunk screw is tightened.

7.3

Installation

7.3.1

Wall Installation

• Fix the instrument mounting plate (2) to the wall with the 4 screws (4) (see Fig. 7.1).
• Fix the transmitter to the instrument mounting plate (2) with the 2 screws (3).

7.3.2

Pipe Installation

Installation on a 2" pipe
• Position the shackles (1) at the pipe (see Fig. 7.1).
• Fix the instrument mounting plate (2) to the shackles with the 4 screws (4).
• Fix the transmitter to the instrument mounting plate (2) with the 2 screws (3).

7.4

Connection of the Transmitter

Attention!

Observe the "Safety Instructions for the Use in Explosive Atmosphere" (see document SIFLUXUS).

Attention!

Observe the "Safety Instructions for the Use in Explosive Atmosphere" (see document SIFLUXUS).

Fig. 7.1: Pipe mounting kit

Attention!

Observe the "Safety Instructions for the Use in Explosive Atmosphere" (see document SIFLUXUS).

Attention!

The degree of protection of the transmitter will only be ensured if the cable glands are firmly tightened
and the front plate and the housing cover are tightly screwed to the housing.

1

2

3

4

5

6

1

shackle

2

instrument mounting plate

3

screw

4

screw

5

front plate

6

housing cover

2

«
...
37
38
39
40
41
...
»

Содержание FLUXUS G800


































































































































































Отзывы:

Нет отзывов

Похожие инструкции для FLUXUS G800

Бренд: jenway Страницы: 20

Бренд: Banner Страницы: 11

Бренд: Bante Instruments Страницы: 10

Бренд: BANTE Страницы: 11

Бренд: Banner Страницы: 14

Бренд: Banner Страницы: 16

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Instruments Страницы: 2

Бренд: Hammond Страницы: 16

Бренд: SAGEMCOM Страницы: 33

Бренд: G-Tek Страницы: 83

Бренд: Midcontinent Страницы: 6

Бренд: Wacom Страницы: 23

EUROGRAND EG2080

Бренд: Behringer Страницы: 34

Бренд: ICP DAS USA Страницы: 4

Бренд: G4M Страницы: 52

83620B 8360 Series

Бренд: Agilent Technologies Страницы: 2

Бренд: Eddy Wireless Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды