FlexiForce ForceIQ Force100XC Скачать руководство пользователя страница 31

Страница: 31 / 42

manual – force

www.flexiforce.com

Settings for the PSE:

•

Use the or buttons to navigate to the "Safety device" menu.

•

Press

to enter the menu.

•

Use the or buttons to select "Safety1". Press

to confirm.

•

Use the or buttons to select "Airwave switch". Press

to confirm.

•

Use the or buttons to select "down full rev.".

•

Press

to confirm and save.

•

Press to return to the main menu.

•

Press once more to enter the maneuvering mode.

settings for the pass door switch:

•

Use the or buttons to navigate to the "Safety device" menu.

•

Press

to enter the menu.

•

Use the or buttons to select "Safety 2". Press

to confirm.

•

Use the or buttons to select "passdoor".

•

Press

to confirm and save.

•

Press to return to the main menu.

•

Press once more to enter the maneuvering mode.

You don't have to adjust the slack rope switch, this is recognized by the control unit

Содержание ForceIQ Force100XC











































Результаты поиска

Содержание ForceIQ Force100XC

Отзывы:

Похожие инструкции для ForceIQ Force100XC

Бренды по названию

Популярные бренды

FlexiForce ForceIQ Force100XC, Руководство пользователя

Результаты поиска

Содержание ForceIQ Force100XC

Отзывы:

Похожие инструкции для ForceIQ Force100XC

Бренды по названию

Популярные бренды