Flavor Burst FB 80-08 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 74

Flavor Burst FB 80-08 Скачать руководство пользователя страница 28

27

NOTE:

BE SURE TO PLACE A CONTAINER

UNDER THE INJECTOR HEAD TO CATCH
THE PRODUCT AND SANITIZER SOLUTION.

NOTE:

YOUR HANDS SHOULD BE CLEANED

AND SANITIZED BEFORE YOU PERFORM
THE FOLLOWING PROCEDURE.

NOTE:

THE FOLLOWING PROCEDURES

REQUIRE APPROVED, SERVICEABLE AND
SANITIZED TOOLS AND BRUSHES.
CONTACT YOUR LOCAL DISTRIBUTOR FOR
RECOMMENDED SUPPLIES.

NOTE:

USE AN APPROVED CLEANER AND

SANITIZER FOR THE FOLLOWING
PROCEDURES. REFER TO
MANUFACTURER’S INSTRUCTIONS FOR
PROPER PREPARATIONS OF THESE
CLEANING AGENTS.

NOTE:

INSPECT ALL WEAR ITEMS AND

REPLACE IF NECESSARY.

Each syrup flavor is stored inside a numbered
tray (1-8) within the system cabinet. Under
normal operating conditions, flavors are
installed as previous flavors become empty.
However, you may change flavors periodically
as desired.

1. Mix approved detergent with warm water

according to manufacturer’s instructions.
Also prepare approved sanitizer solution

according to manufacturer’s instructions.

2. Complete “CIP – Phase 2” of the Clean-In-

Place procedure in the SCHEDULED
MAINTENANCE section for the
corresponding syrup line. Do not perform
Step 22.

NOTE:

BE SURE TO PLACE A CONTAINER

UNDER THE INJECTOR HEAD TO CATCH
THE PRODUCT AND SANITIZER SOLUTION.

3. Pull the tray forward and remove the syrup

bag. Discard the syrup bag if it is empty or
expired. If the bag has usable syrup, store
the syrup as directed on the label. (See
Figure 40.)

Figure 40

4. Clean the syrup tray with a single service

towel and detergent water, rinse and dry
thoroughly. (See Figure 41.)

Figure 41

5. Select the flavor you wish to use, then place

the bag on the table with the fitment up and
remove the dust cap. (See Figure 42.)

Figure 42

REPLACING THE SYRUP FLAVORS

«
...
26
27
28
29
30
...
»

Содержание FB 80-08











































































Отзывы:

Нет отзывов