manualshive.com logo in svg

Fischer Panda 45i pms, Руководство пользователя

Поделиться
Скачать
Fischer Panda 45i pms Скачать руководство пользователя страница 53

Generator operation instruction

8.10.14

Kapitel/Chapter 5: Generator operation instruction   -   Seite/Page 53

5. Generator operation instruction

5.1

Personal requirements

Only instructed persons are allowed to run the generator. Instructed Persons has read the manual of the generator
and all ancillary components and external equipment. He must be acquaint with the specific risks and safety instruc-
tions. 

Only persons who are expected to perform their tasks reliably are permitted as personnel. Persons whose reaction
capability is impaired, e.g. through drugs, alcohol or medication are not permitted.

When selecting the personnel, the stipulations regarding age and occupation applying at the location must be
observed.

5.2

Hazard notes for the operation

Notice!:

Please note the safety first instructions in front of this 
manual.

Warning!: Automatic start

Danger for life! - The generator can be equipped with a 
automatic start device. This means the generator can be 
started by an external signal. 

To avoid an unexpected starting of the generator, the starter 
battery must be disconnected before start working at the 
generator.

Attention!: Danger to life

Rotating parts inside of the generator

Do not run the generator with removed sound cover. If it is 
necessary to test the generator without sound cover, pay 
special attention. Never do this work alone. Do all service, 
maintenance and repair with engine stopped. 

Attention!: Danger to Life - High voltage

Danger for Life. Improper handling, operation, 
installation and maintenance can result in severe 
personal injury and/or material damage.

Electrical voltages above 48 volts (battery chargers greater 
than 36 volts) are always dangerous to life). The rules of the 
respective regional authority must be adhered to. Only an 
electrician may carry out installation of the electrical 
connections for safety reasons.

5.3

General operating instruction

5.3.1  Operation at low temperatures

The Generator can be started at temperatures down to - 20 °C, therefor the operation fluids like fuel, cooling water,

Содержание 45i pms





















































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды