manualshive.com logo in svg

Fischer Panda 45i pms, Руководство пользователя

Поделиться
Скачать
Fischer Panda 45i pms Скачать руководство пользователя страница 194

General operation

Seite/Page 194   -   Kaptitel/Chapter 2: General operation

8.10.14

Fig. 2.4.6-1: Set-up menu

To activate the autostart function, select the item 
"Autostart" in the set-up menu using the cursor buttons 
and confirm the selection with the Start/Stop button.

Fig. 2.4.6-2: "Autostart" sub-menu

In the "Autostart" sub-menu, you can select between the 
options "Enable" and "Disable" using the cursor 
buttons:

To activate the autostart function, select "Enable" and again 
confirm your selection with the Start/Stop button. 

To deactivate the function, use the menu item "Disable". 

The Panda iControl will then confirm your input:

Fig. 2.4.6-3: Message "Autostart enabled" after confirming the 

selection

Message "Autostart enabled" after confirming the 
selection

Fig. 2.4.6-4: Message "Autostart disabled" after confirming the 

selection

Message "Autostart disabled" after confirming the 
selection

Fig. 2.4.6-5: Selection is saved to the EEPROM

The activation/deactivation of the autostart function is 
then saved to the EEPROM of the control panel. 

Содержание 45i pms





















































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды