Fimap 109070 Скачать руководство пользователя страница 63

Страница: 63 / 104

4.8

Disassembly

4.8.1

Brush Flange

Remove the brush.
Insert the Allen key and unscrew it in the opposite direction of
the working brush.
Then proceed with the removal of the flange

4.8.2

56 Brush Deck

Remove the brush, close the water, lower the brushdeck and turn
the machine Off.
Remove the batteries, and disconnect the brush motor power
connector (A).

Release the compensation spring.
Unscrew the right and left screws (B).
At the base of the gear, disconnect the water flow tube.

Lift the front of the machine with a suitable lifting system.
At this point remove the base (C) from the left side.

4.8.3

Brush Deck Actuator

Lower the base and turn off the machine.
Lift the seat and remove the water system screws (A) to access
the actuator connector.

Содержание 109070









































































































Результаты поиска

Содержание 109070

Отзывы:

Похожие инструкции для 109070

Бренды по названию

Популярные бренды

Fimap 109070, Руководство по обслуживанию

Результаты поиска

Содержание 109070

Отзывы:

Похожие инструкции для 109070

Бренды по названию

Популярные бренды