background image

FIB_FGS-221

Relay Insert 2 * 1.5 KW

Firmware Version : 1.3

Quick Start

To include the Fibaro Switch relay into the network, set the Home Center controller into the inclusion mode 

and then press the button of the device or the push-button B located inside the housing of the switch relay 

three times during 1.5 seconds. The LED will become green for 3 seconds and then turn off. The device is 

now ready to work.

Please refer to the chapters below for detailed information about all aspects of the products usage.

What is Z-Wave?

This device is equipped with wireless communication complying to the Z-Wave standard. Z-Wave is the 

international standard for wireless communication in smart homes and buildings. It is using the 

frequency of 868.42 MHz to realize a very stable and secure communication. Each message is reconfirmed 

(two-way communication) and every mains powered node can act as a repeater for other nodes (meshed 

network) in case the receiver is not in direct wireless range of the transmitter.

Z-Wave differentiates between Controllers and Slaves. Slaves are either sensors (S) transmitting metered or 

measured data or actuators (A) capable to execute an action. Controllers are either static mains powered 

controllers (C) also referred to as gateways or mobile battery operated remote controls (R). This results in a 

number of possible communication patterns within a Z-Wave network that are partly or completely supported 

by a specific device.

(c) 2016 Z-Wave Europe GmbH, Antonstr. 3, 09337 Hohenstein-Ernstthal, Germany, All rights reserved, www.zwaveeurope.com - pp 1 

Содержание FGS-221













Отзывы: