manualshive.com logo in svg

Festo CMMS-ST-*-G2 Series, Сборка и инструкция по установке

Поделиться
Скачать
Festo CMMS-ST-*-G2 Series Скачать руководство пользователя страница 36

 

3. Product description 

36  

Festo.P.BE-CMMS-ST-G2-HW-EN 

1008NH 

Setting the operating mode 

Due to a necessary synchronisation of internal processes, the change of operation mode 
can require some cycle times of the controller. We therefore recommend that you always 
verify and wait for reception of the desired operation mode. 

 

Operating mode 

Syntax 

Response 

Regulating torque  

OW:0030:00000004  

Speed adjustment  

OW:0030:00000008  

Positioning  

OW:0030:00000002  

OK! or OW:EEEEEEEE 

Table 

 

3.12 Operating mode 

Faulty return values can be called up due to invalid values that do not come from the 
above-named group. The current operation mode can be read by using the “OR” 
command. 

Control via RS-485 

 

 

Note 

Before activating the RS-485 interface, please make sure that you 
are using a completely wired null modem cable. All pins of the 
cable must be occupied according to the following specification 
(also see chapter 

 

6.4.5). 

 
 

Pin Brief 

description 

Name Signal 

direction 

Description 

1 DCD 

Data 

carrier 

detect 

Transfer device --> 
end device 

Data carrier signal was recorded by 
transfer device. 

2 

RxD 

Receive (x) Data 

Transfer device --> 
end device 

Line at the end device that receives a 
data bit from the transfer device. 

3 

TxD 

Transmit (x) Data 

End device -->  
Transfer device 

Line at the end device that sends a data 
bit to the transfer device. 

4 DTR 

Data 

terminal 

ready 

End device -->  
Transfer device 

End device is ready for use. 

5 

GND 

Ground (earth) 

None 

Reference potential at 0 V. 

6 

DSR 

Data set ready 

Transfer device --> 
end device 

Transfer device is ready for use. 

7 

RTS 

Request to send 

End device -->  
Transfer device 

End device displays that the remote 
station should send (send request). 

8 

CTS 

Clear to send 

Transfer device --> 
end device 

Transfer device shows reception 
readiness (send permission). 

Содержание CMMS-ST-*-G2 Series









































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды