manualshive.com logo in svg

Festo CMMS-ST-*-G2 Series, Сборка и инструкция по установке

Поделиться
Скачать
Festo CMMS-ST-*-G2 Series Скачать руководство пользователя страница 124

 

8. Service functions and error messages 

124  

Festo.P.BE-CMMS-ST-G2-HW-EN 

1008NH 

Error message 
Main 
index 

Sub-
index 

Meaning of error 
message 

Measures Error 

reaction 

21 

0 

Fault in offset current 
measurement 

Error cannot be self-corrected. 
Send the stepping motor controller to the 
manufacturer. 

PS off 

0 PROFIBUS: 

Faulty initialisation 

Expansion module defective? 
Please contact Technical Support. 

PS off 

1)

 

22 

2 Communication fault 

PROFIBUS 

Check set slave address 
Check bus connection 
Check cables 

PS off 

1)

 

25 

1 

Hardware error 

Motor controller and firmware are not 
compatible.  
Update the firmware. 

PS off 

26 1 Checksum 

error 

Error 

cannot be self-corrected. 

Please contact Technical Support. 

PS off 

0 

No SD 

Tried to access missing SD card. 

Warn 

1)

 

1 

SD initialisation error 

Error on initialisation 
communication not possible. 

PS off 

1)

 

29 

2 

SD parameter record error Checksum incorrect 

File missing 
Incorrect file format 
Error when saving the parameter file to the 
SD card 

PS off 

1)

 

0 

I²t motor (I²t at 100%) 

I²t monitoring of the motor has responded; 
motor/mechanical system blocked or 
sluggish? 

Warn 

1)

 

31 

1 

I²t controller (I²t at 100%) I

²

t monitoring of the controller has 

responded. Check power dimensioning of 
drive package.  

PS off 

1)

 

35 

1 

Timeout for quick stop 

The parameterised time for quick stop was 
exceeded 

PS off 

0 

Fault: SW limit switch 
reached 

Negative software limit switch reached.  

1 

Fault: SW limit switch 
reached 

Positive software limit switch reached.  

2 

Fault: SW limit switch 
reached 

Target position is behind the negative 
software limit switch.  

40 

3 

Fault: SW limit switch 
reached 

Target position is behind the positive 
software limit switch.  

Warn 

1)

 

Содержание CMMS-ST-*-G2 Series









































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды