manualshive.com logo in svg

Festo CMMS-ST-*-G2 Series, Сборка и инструкция по установке

Поделиться
Скачать
Festo CMMS-ST-*-G2 Series Скачать руководство пользователя страница 118

 

7. Preparations for commissioning 

118  

Festo.P.BE-CMMS-ST-G2-HW-EN 

1008NH 

7.4

 

Connecting the CMMS-ST stepping motor 
controller to the power supply 

 

Connecting the 
stepping motor 
controller 

1.

 

Make sure that the power supply is switched off. 

2.

 

Insert the PHOENIX plug into the socket [X9] on the device. 

3.

 

Connect the 24 V connection to a suitable power pack. 

4.

 

Connect the power supply unit. 

5.

 

Check all plug connectors once again. 

7.5

 

Connecting a PC 

 

Connecting a PC 

1.

 

Insert the D-sub plug of the serial interface cable into the socket 
for the serial interface of the PC and secure the locking screws. 

2.

 

Insert the D-sub plug of the serial interface cable into socket 
[X5] RS232/COM for the CMMS-ST stepping motor controller 
and secure the locking screws. 

3.

 

Check all plug connectors once again. 

7.6

 

Checking readiness for operation 

 

Checking readiness 
to operate 

1.

 

Make sure that the controller enable switch is switched off. 

2.

 

Switch on the power supplies for all devices. The READY LED on 
the front of the device should now light up. 

 

 

If the READY LED does not light up, there is a fault. If the seven 
segment display shows a number sequence, this is an error 
message. You must rectify the cause of the message. If this is the 
case, see chapter 

 

8.2 Error messages (page 122). If no display 

lights up on the device, proceed as follows: 

No display lights up  1.

 

Switch off the supply voltage. 

2.

 

Wait for one minute to allow the intermediate circuit to 
discharge. 

3.

 

Check all connecting cables. 

4.

 

Check that the 24 V control voltage is functional. 

5.

 

Switch on the supply voltage again. 

Содержание CMMS-ST-*-G2 Series









































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды