EN
10
4.5 USING THE UPPER SURFACE (Fig. 11)
ATTENTION: It is absolutely forbidden to use the
upper surface for cutting steel and aluminium.
To use the upper surface act as follows:
- Make sure stop knob
51
is disengaged (protruding).
- Lower the blade unit completely and lock it into place
with pivot
19
- Release levers
25
and select the height of the upper
surface, then lock the levers back into place.
4.6 USING THE END-STROKE GUIDE FOR THE
UPPER SURFACE (Fig. 11)
To use, act as follows
- Fit guide
17
in the upper surface.
- Select the cut width by means of the graduated scale.
- Lock guide
37
, with lever
17
, making sure that the guide
is aligned with the blade.
4.7 CUTTING SMALL PIECES
Working operations with small sized pieces must be carried
out using the special tools.
- On the lower surface: use the clamp to fi t the piece
and the end stroke shafts in order to attain the desired
measure..
- On the upper surface: use the special pushers in order
to move the piece forward (see fi gure of exsmple).
The pusher must be applied to a wooden support
(see
Fig. 12)
.
4.8 INSTALLATION AND/OR REPLACEMENT OF THE
BLADE (Fig.13)
ATTENZIONE: these operations must be carried
out only after having stopped the motor of the
machine releasing the switch 2 and after having
removed the plug from the electric socket.
- Raise up the table up to its maximum height.
- Take the two hexagonal keys 6mm included in the
machine: insert one key in terminal
41
of motor shaft
and the other one in the blade fi xing screw
42
. Now
unfasten the screw, paying attention that the thread is
from right to left.
- Take off the external fl ange
43
, push the pawl
40
and
at the same time raise up the protection
11
and keep it
high in order to uncover the blade.
- Disassembly the blade taking it off from the inferior part
of the head and assembly the new blade.
- Pay attention through visual control to assembly the
blade with the teeth oriented on the same direction as
indicated from the arrow on the blade.
- Now release the protection
11
, assembly again the
external fl ange
43
, fasten again the screw
42
and
fasten it properly with the hexagonal keys included in
the machine.
- Pull down the table.
4
OPERATION AND USE
4.1 USING THE MITRE SAW (Fig. 8)
ATTENTION: Make sure that the pushbutton 51 is
released (protruding).
- Bring the upper surface up to the maximum height.
- Firmly fi x the material to be cut to the cutting top..
ATTENTION: when cutting aluminium sections
the use of a clamp is indispensable.
- Start up and wait for the blade to reach max. speed.
- gradually lower the blade unit and cut.
ATTENTION: Pressing on the handgrip stronger
will not reduce cutting time, but may cause
reduced effi
ciency due to motor overload.
4.2 BLADE START AND STOP (Fig. 8)
ATTENTION: Check that the mobile protection 11
casings are correctly positioned when the blade
is in its rest position (raised)
The machine is equipped with a release pushbutton which
starts and stops the blade.
The pushbutton can be locked in “ON” position pressing key
51
when switch lever
52
is at the end of its travel and motor
is running
(see switch operating instructions)
ATTENTION: The use of this locking device
disables the safety device provided by the
manufacturer and enables pushbutton start. we
advise that this device be used with maximum
care and ONLY when the machine is used as a
circular saw.
To unlock the switch, press the button
51
and release the
52
switch lever.
4.3 USING THE END-STROKE SHAFTS (Fig. 9)
To use the shafts act as follows:
- Insert shaft
26
in the support plate and lock into position
with knob
27
.
- Loosen knob
28
and adjust shaft
29
according to the
length of the piece, referring to the ruler marked off in
mm. Lock into position with knob
28
.
4.4 USING A CLAMP (Fig. 10) (OPTIONAL)
To use the clamp act as follows:
- position guide shaft
44
locking it with the screw.
- Fit clamp
46
into guide and lock it into place with lever
45
.
- Adjust clamp opening by means of lever
45
or knob
47
.
