manualshive.com logo in svg

Federal Signal Corporation Informer100 Speaker, Руководство пользователя

Поделиться
Скачать
Federal Signal Corporation Informer100 Speaker Скачать руководство пользователя страница 48

48

  

  

Programming

Informer100 Speaker (Models IS-I-IP100ACX and IS-I-IP100DCX) 

Federal Signal 

www.fedsig.com

2. 

Click Apply to restore your settings to the factory defaults.

3. 

Reboot the device for the changes to take effect.

If the configuration details are lost or changed incorrectly and it becomes necessary 

to restore the Informer to factory default settings, perform a Power-On Factory Default 

procedure. 

Restoring the Informer-IP to Factory Default

The Informer-IP can be restored to the factory default by either using the web pages or 

the RESET button.

Using the Web Pages

To restore the configuration to the factory default by using the web pages:

1. 

Navigate to the IP address of the Informer using a web browser and log in.

2. 

Select Factory Default. Include or Exclude Network Settings. 

3. 

Click Apply to restore your settings to the factory defaults.

4. 

Reboot the device for the changes to take effect.

Using the RESET Button

To restore the configuration to the factory default by using the RESET button:

1. 

Remove power from the Informer.

2. 

Press and hold down the RESET button.

3. 

Apply power while holding down the RESET button until the Power and Test LEDs 

begin to blink, confirming that the default configuration has been loaded.

You must reenter all local configuration settings before placing the Informer into service.

Restoring the Informer100 and IS-I-IP15 to Factory Default

The Informer100 and IS-I-IP15 can be restored to the factory default by either using the 

web pages or Factory Default Jumper. 

Using the Web Pages

To restore the configuration to the factory default by using the web pages:

1. 

Navigate to the IP address of the Informer using a web browser and log in.

2. 

Select Factory Default. Include or Exclude Network Settings. 

3. 

Click Apply to restore your settings to the factory defaults.

4. 

Reboot the device for the changes to take effect.

Using Factory Default Jumper

To restore the configuration to the factory default using the factory default jumper:

1. 

Apply power to the Informer for at least 60 seconds to allow it to boot.

2. 

Short JP11 on the control board for 10 seconds, and then remove the short.  

3. 

Wait 60 seconds for the Informer to reboot with the factory default settings. 

Содержание Informer100 Speaker





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды