manualshive.com logo in svg

Federal Signal Corporation Informer100 Speaker, Руководство пользователя

Поделиться
Скачать
Federal Signal Corporation Informer100 Speaker Скачать руководство пользователя страница 15

15

Installation

Signaling Standalone Manual 

Federal Signal 

www.fedsig.com

Figure 6 Ceiling mount

Pole Mounting 

The Informer100 comes standard with a bracket for vertical wall or pole mount with 

optional pole accessories. 

Large Pole Mounting (6 in diameter or larger)

Use the following procedure if mounting the speaker with the optional IS-I-IP100-PMW 

bracket:

1. 

Find a suitable location to mount the speaker. Use industry- or company-preferred 

practices when mounting hardware to poles or other structures.

2. 

Attach the IS-I-IP100-PMW bracket to the pole using banding or use the pre-drilled 

holes to bolt the bracket to the pole or structure.

3. 

Using the supplied flat washers, lock washers, and 3/8 inch nuts, mount the speaker 

to the IS-I-IP100-PMW bracket as shown in Figure 2.

4. 

Use the side pivot bolts to allow adjustment of the speaker up and down to optimize 

speaker effectiveness.

Figure 7 Bracket IS-I-IP100-PMW

  

Содержание Informer100 Speaker





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды