manualshive.com logo in svg

Federal Signal Corporation Informer100 Speaker, Руководство пользователя

Поделиться
Скачать
Federal Signal Corporation Informer100 Speaker Скачать руководство пользователя страница 25

25

Installation

Signaling Standalone Manual 

Federal Signal 

www.fedsig.com

Figure 16 AC Controller Board with optional Strobe

Ethernet Port

The Informer100 Speaker has an eight-pin Ethernet port for connecting to the network. 

Ethernet wire runs must be less than 328 feet from the nearest network switch. Do not 

install in a conduit carrying high voltage. The wired Ethernet port auto-negotiates a 

10/100, full or half duplex connection.

Putting the Informer100 Speaker into Standalone Mode

Standalone mode allows the Informer100 Speaker to be activated from the Alarm Initiation 

Inputs without being connected to a network. The Informer100 requires setup prior to 

placing it into standalone mode. All configuration should be performed prior to installing. 

Once the unit is configured and tested, place a shorting jumper across pins 1 and 2 of 

JP3. 

Содержание Informer100 Speaker





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды