manualshive.com logo in svg

Fayat Dynapac DFP11, Руководство по эксплуатации, Страница: 96 / 112

Поделиться
Скачать
Fayat Dynapac DFP11 Скачать руководство пользователя страница 96

8.9  As required

8.9.1  Cleaning the cooling fins and the cooling air intake openings

How dirty the cooling fins and cooling air intake

openings are depends very much on the daily

operating conditions; clean daily if necessary.

NOTICE!
Danger of engine damage caused by reduced

cooling!

–

For this reason you should always seal any oil

or fuel leaks in the vicinity of the cooling fan or

the coolers and clean the cooling fins after.

Protective equipment:

n

Working clothes

n

Protective gloves

n

Safety goggles

1.

Park the machine safely

 

Ä

 Chapter 6.5 ‘Parking the machine

in secured condition’ on page 65

.

2.

Allow the engine to cool down.

3.

Remove dried dirt with a suitable brush from all cooling fins

and cooling air intake openings.

4.

CAUTION!
Danger of eye injuries caused by particles

flying around!

–

Wear your personal protective equipment

(safety gloves, protective working

clothes, goggles).

Blow out the cooling fins and cooling air intake openings with

compressed air.

If the engine is oily, use a cold cleansing agent for cleaning.

Fig.  100

Cleaning with cold cleansing agent

Maintenance – As required

 

DFP11

 

96

Содержание Dynapac DFP11

















































































































Отзывы:

Нет отзывов