manualshive.com logo in svg

Fayat Dynapac DFP11, Руководство по эксплуатации, Страница: 86 / 112

Поделиться
Скачать
Fayat Dynapac DFP11 Скачать руководство пользователя страница 86

1.

Hold the hexagon nut (1) on the rocker arm and loosen

counter nut (2).

2.

Adjust the hexagon nut, until the feeler gauge can be

inserted and pulled out with little resistance after retightening

the counter nut.

1.

Install the valve cover (2) with a new seal (3).

2.

Tighten the fastening screws (1) evenly.

3.

After a short test run, check the engine for leaks.

8.8.3  Cleaning the slurry filter and fuel strainer

DANGER!
Danger to life caused by explosive gas-air

mixes!

–

Do not allow gasoline to come into contact with

hot components.

–

Smoking and open fire is prohibited.

–

Keep away from heat sources, sparks and

other sources of ignition.

–

Do not spill any gasoline.

Protective equipment:

n

Working clothes

n

Safety shoes

n

Protective gloves

1.

Park the machine safely

 

Ä

 Chapter 6.5 ‘Parking the machine

in secured condition’ on page 65

.

2.

Allow the engine to cool down.

Adjusting the valve clearance

Fig.  75

Final work

Fig.  76

Maintenance – Annually

 

DFP11

 

86

Содержание Dynapac DFP11

















































































































Отзывы:

Нет отзывов