manualshive.com logo in svg

Fayat Dynapac CC1100 VI, Инструкция по эксплуатации, Страница: 41 / 233

Поделиться
Скачать
Fayat Dynapac CC1100 VI Скачать руководство пользователя страница 41

Machine description

4812164501.pdf

2021-05-06

Machine description

Diesel engine

The machine is equipped with a water-cooled, in-line
three or four cylinder, four-stroke diesel engine.

Electrical system

The machine has the following control units (ECU,
Electronic Control Unit) and electronic units.

• Main ECU (for the machine)

• Engine-ECU:

CC1100 VI / CC1200 VI

 - for D1803-CR (Tier 4f, Stage V

(28 kW))

CC1300 VI / CC1400 VI

 - for V2403-CR (Tier 4f, Stage V

(37 kW))

Propulsion system/Transmission

The propulsion system is a hydrostatic system with a
hydraulic pump supplying two motors connected in
parallel.
The motors drive the front and rear drums.

The speed of the machine is proportional to the
deflection/angle of the control lever from neutral.

Brake system

The brake system consists of a service brake,
secondary brake and parking brake.
The service brake is hydrostatisc and is activated by
moving the control lever to neutral.

Secondary/Parking brake

The secondary and parking brake system consists of
sprung multiple disc brakes in the motors. The brakes
are released with hydraulic pressure and are operated
with a switch on the instrument panel.

Steering system

The steering system is a hydrostatic system.
The control value on the steering column distributes
the flow to the control cylinder, which actuates the
articulation.
The steering angle is proportional to the deflection of
the steering wheel.

ROPS

ROPS is the abbreviation for "Roll Over Protective
Structure".

If any part of the ROPS structure's protective
construction displays plastic deformation or cracks, the

27

Содержание Dynapac CC1100 VI










































































































































































































































Отзывы:

Нет отзывов