Fayat Dynapac CC1100 VI Скачать руководство пользователя страница 103 | Manualshive

Страница: 103 / 233

Fayat Dynapac CC1100 VI Скачать руководство пользователя страница 103

Miscellaneous

4812164501.pdf

2021-05-06

Towing the roller

Fig. Towing

The roller must be counter-braked during
towing/recovery. Always use a towbar. There is no
braking capacity on the roller now.

The roller must be counter-braked during
towing/recovery. Always use a towbar. There is no
braking capacity on the roller now.

The roller must be towed slowly, max. 3 kph (2
mph) and only towed short distances, max. 300 m
(1000 ft).

The roller must be towed slowly, max. 3 kph (2
mph) and only towed short distances, max. 300 m
(1000 ft).

When towing/retrieving a machine, the towing device
must be connected to both lifting holes. The pulling
force shall act longitudinally on the machine as shown
in the figure.

Maximum total pulling force:

- CC1100 VI / CC1200 VI 39 kN (9.767 lbf)

- CC1300 VI / CC1400 VI 63 kN (14.163 lbf)

Reverse the towing preparations.

Reverse the towing preparations.

Fig. Bracket, towing - front

Fig. Bracket, towing - rear

89

«
...
101
102
103
104
105
...
»

Содержание Dynapac CC1100 VI










































































































































































































































Отзывы:

Нет отзывов