Fayat Dynapac CC1100 VI Скачать руководство пользователя страница 194

Страница: 194 / 233

Maintenance - 2000h

4812164501.pdf

2021-05-06

Engine oil and oil filter - Change

Fig. Engine compartment right side -
D1703-E3B (Stage IIIA)
1. Drain hose
2. Drain plug
3. Filler cap
4. Oil filter

Run the engine until it is warm before draining the oil .

Switch off the engine and push in the emergency
stop.

Take great care when draining fluids and oils.
Wear protective gloves and goggles.

Fig. Engine compartment, right side -
D1703-E4B (Tier 4f / Stage V)
1. Drainage hose
2. Drain plug
3. Filler cap
4. Oil filter

Place a receptacle that holds at least 12 liters (8 gal.)
under the drain plug (2).

Undo the oil filler cap (3), and undo the drain plug (2)
in the end of the drain hose (1). Let all the engine oil
flow out.

Deliver the drained oil to special waste handling.

Refer to the engine manual for detailed
instructions when changing oil and filters.

180

Содержание Dynapac CC1100 VI










































































































































































































































Результаты поиска

Содержание Dynapac CC1100 VI

Отзывы:

Fayat Dynapac CC1100 VI, Инструкция по эксплуатации, Страница: 194 / 233

Результаты поиска

Содержание Dynapac CC1100 VI

Отзывы: