Fayat Dynapac CC1100 VI Скачать руководство пользователя страница 195 | Manualshive

Страница: 195 / 233

Fayat Dynapac CC1100 VI Скачать руководство пользователя страница 195

Maintenance - 2000h

4812164501.pdf

2021-05-06

Fig. Engine compartment, right side -
D1803-CR (Tier 4f / Stage V)
1. Drainage hose
2. Drain plug
3. Filler cap
4. Oil filter

1

3

2

4

Remove the oil filter (4).

Collect any spillage.

Install the new filter.

Fit the drain plug (2) to the end of the hose.

Fill with fresh engine oil. See under the heading
lubricants, for the correct oil grade. Fit the filler cap (3)
and check that the oil level is correct using the dipstick.

Start the engine and allow it to idle for a few minutes.
During this time, check around the oil filter and drain
plug for leaks.

Switch off the engine, wait for a minute or so and then
check the oil level. Top up with more oil if necessary.

4

3

2

Fig. Engine compartment right side -
V2203-M (Stage IIIA)
2. Drain plug
3. Filler cap
4. Oil filter

2

3

4

Fig. Engine compartment right side -
V2403-CR (Tire 4f / Stage V)
2. Drain plug
3. Filler cap
4. Oil filter

181

«
...
193
194
195
196
197
...
»

Содержание Dynapac CC1100 VI










































































































































































































































Отзывы:

Нет отзывов