Fayat Dynapac CC1100 VI Скачать руководство пользователя страница 26

Страница: 26 / 233

Special instructions

4812164501.pdf

2021-05-06

Do not spray with high-pressure cleaner directly onto
gaskets and bearing spacings in steering hitch and
drum, and electronics.

Never aim the water jet directly at the fuel tank
cap, or into exhaust pipe. This is particularly
important when using a high-pressure cleaner.

Fire fighting

If the machine catches fire, use an ABC-class powder
fire extinguisher.

A BE-class carbon dioxide fire extinguisher can also
be used.

Fire extinguisher

Fig. Plarform
1. Fire extinguisher

A fire extinguisher can be ordered as an option.
Though, different standards are used around the world.

If not using the original fire extinguisher, place your
extinguisher as in the picture. A 4 kg extinguisher is
recommended.

Mount it appropriately and make sure it does not
create any hazards.

Roll Over Protective Structure (ROPS)

Never carry out any welding or drilling in the
Roll Over Protective Structure (ROPS).

Never repair a damaged ROPS structure, it must
be replaced with a new one.

Содержание Dynapac CC1100 VI










































































































































































































































Результаты поиска

Содержание Dynapac CC1100 VI

Отзывы:

Fayat Dynapac CC1100 VI, Инструкция по эксплуатации, Страница: 26 / 233

Результаты поиска

Содержание Dynapac CC1100 VI

Отзывы: