Fayat Dynapac CC1100 VI Скачать руководство пользователя страница 220

Страница: 220 / 233

Maintenance, 3000h

4812164501.pdf

2021-05-06

Replacing the fuel filter

Fig. Engine compartment, right side
1. Fuel filter

Place a container underneath to collect fuel that
runs out when the filter is released.

Screw off the fuel filter (1). The filter is of the
disposable type and cannot be cleaned. Hand in to a
waste disposal site.

Install the new filter.

Start the engine and check that the fuel filter is tight.

Refer to the engine manual for detailed
instructions when replacing the fuel filter.

Ensure good ventilation (air extraction) if the
diesel engine is run indoors. Risk of carbon
monoxide poisoning.

Replacing the pre-filter

Fig. Engine compartment -
D1703-M-IDI-E3 (Stage IIIA) /
V2203-M-E3B (Stage IIIA)
1. Pre-filter
2. Hose clamps
3. Fuel pump

Activate the parking brake.
Switch off the engine and open the engine hood.

Place a container underneath to collect fuel that
runs out when the filter is released.

206

Содержание Dynapac CC1100 VI










































































































































































































































Результаты поиска

Содержание Dynapac CC1100 VI

Отзывы:

Fayat Dynapac CC1100 VI, Инструкция по эксплуатации, Страница: 220 / 233

Результаты поиска

Содержание Dynapac CC1100 VI

Отзывы: