Fayat Dynapac CC1100 VI Скачать руководство пользователя страница 141

Страница: 141 / 233

Maintenance, 10h

4812164501.pdf

2021-05-06

Fig. Pump system
1. Water filter
2. Drain cock
3. Water pump

When cleaning the coarse filter (1), open the cock (2)
and loosen the filter housing.

Clean the filter and filter housing. Check that the
rubber gasket in the filter housing is intact.

After inspecting and carrying out any necessary
cleaning, start the system and check that it works.

Sprinkler system/Drum
Cleaning of sprinkler nozzle

Figure. Nozzle
1. Nozzle
2. Gasket
3. Filter

Dismantle the blocked nozzle by hand.

Blow the nozzle (1) and fine filter (3) clean using
compressed air. Alternatively, fit replacement parts
and clean the blocked parts later on.

Nozzle

Colour

l/min (at 2.0
bar)

gal/min (at
40 psi)

Nozzle

Colour

l/min (at 2.0
bar)

gal/min (at
40 psi)

Standard

yellow

0.63

0.20

Standard

yellow

0.63

0.20

Option

blue

0.98

0.30

Option

blue

0.98

0.30

Option

red

1.31

0.40

Option

red

1.31

0.40

Option

brown

1.63

0.50

Option

brown

1.63

0.50

After inspecting and carrying out any necessary
cleaning, start the system and check that it works.

Wear protective goggles when working with
compressed air.

127

Содержание Dynapac CC1100 VI










































































































































































































































Результаты поиска

Содержание Dynapac CC1100 VI

Отзывы:

Fayat Dynapac CC1100 VI, Инструкция по эксплуатации, Страница: 141 / 233

Результаты поиска

Содержание Dynapac CC1100 VI

Отзывы: