Fayat BOMAG BVP 10/36 Скачать руководство пользователя

Страница: 96 / 112

Check the condition of the spark plug, clean if necessary.

In case of excessive combustion residues or burned off elec-

trodes, replace the spark plug

Chapter 8.8.1 „Replacing

the spark plug“ on page 80

Check the electrode gap of the spark plug with a feeler

gauge, if necessary, adjust the gap.

Nominal value:

0.7 - 0.8 mm (0.028 - 0.032 in)

Carefully screw in the spark plug by hand.

Once the sealing surface of the used spark plug is in contact,

tighten for another 1/8 to 1/4 turn with the spark plug

spanner.

NOTICE!
Danger of engine damage caused by a loose

spark plug!

–

Always screw the spark plug in correctly.

8.9.6 Measures if there is a risk of frost

Park the machine safely

Chapter 6.5 „Parking the machine

in secured condition“ on page 62

Remove the cap (1) from the water tank.

Remove the rubber caps (3) from the spray tube.

Open shut-off valve (2) and drain off all water.

Insert the rubber caps.

Close the shut-off valve.

Close the cap.

Fig. 99

Fig. 100

Maintenance – As required

BVP 10/36

Содержание BOMAG BVP 10/36

















































































































Результаты поиска

Содержание BOMAG BVP 10/36

Отзывы:

Похожие инструкции для BOMAG BVP 10/36

Бренды по названию

Популярные бренды

Fayat BOMAG BVP 10/36, Инструкция по эксплуатации

Результаты поиска

Содержание BOMAG BVP 10/36

Отзывы:

Похожие инструкции для BOMAG BVP 10/36

Бренды по названию

Популярные бренды