Fayat BOMAG BVP 10/36 Скачать руководство пользователя страница 46

Страница: 46 / 112

5.1 Notes on safety

If the following tests reveal damages or other defects, the machine

must not be operated, until these deficiencies have been corrected.

Do not operate the machine with defective indicators and control

elements.

Safety installations must not be removed or made ineffective.

Do not change any fixed settings.

WARNING!
Health hazard caused by fuels and lubricants!

–

Safety regulations and environmental protec-

tion regulations must be followed when han-

dling fuels and lubricants

Chapter 3.4 „Han-

dling fuels and lubricants“ on page 23

WARNING!
Danger of injury caused by rotating parts!

–

Before starting work on the machine make sure

that the engine can not be started.

Park the machine safely

Chapter 6.5 „Parking the machine

in secured condition“ on page 62

Checks prior to start up – Notes on safety

BVP 10/36

Содержание BOMAG BVP 10/36

















































































































Результаты поиска

Содержание BOMAG BVP 10/36

Отзывы:

Бренды по названию

Популярные бренды

Fayat BOMAG BVP 10/36, Инструкция по эксплуатации

Результаты поиска

Содержание BOMAG BVP 10/36

Отзывы:

Бренды по названию

Популярные бренды