Faulhaber MC 5004 Скачать руководство пользователя страница 19

Страница: 19 / 53

4th edition, 9-11-2018

7000.05050, 4th edition, 9-11-2018

7000.05050

CANopen protocol description

RxPDO2: Controlword, target position (PP)

The RxPDO2 contains the 16-bit controlword and the 32-bit value of the destination posi-
tion (object 0x607A) for the Profile Position mode (PP).

TxPDO2: Statusword, Position Actual Value

The TxPDO2 contains the 16-bit statusword and the 32-bit value of the actual position
(object 0x6064).

RxPDO3: Controlword, target velocity (PV)

The RxPDO3 contains the 16-bit controlword and the 32-bit value of the set speed
(object 0x60FF) for the Profile Velocity mode (PV).

TxPDO3: Statusword, Velocity Actual Value

The TxPDO3 contains the 16-bit statusword and the 32-bit value of the actual speed (object
0x606C).

RxPDO4: Controlword, target torque

The RxPDO4 contains the 16-bit controlword and the 16-bit value of the target torque
(object 0x6071) for Cyclic Torque Mode (CST).

TxPDO4: Statusword, torque actual value

The RxPDO4 contains the 16-bit statusword and the 16-bit value of the actual torque
(object 0x6077) for Cyclic Torque mode (CST).

11-bit identifier

6 bytes user data

0x300 (768d) +
node ID

LLB

LHB

HLB

HHB

11-bit identifier

6 bytes user data

0x280 (640d) +
node ID

LLB

LHB

HLB

HHB

11-bit identifier

6 bytes user data

0x400 (1024d) +
node ID

LLB

LHB

HLB

HHB

11-bit identifier

6 bytes user data

0x380 (896d) +
node ID

LLB

LHB

HLB

HHB

11-bit identifier

6 bytes user data

0x400 (1024d) +
node ID

LLB

LHB

HLB

HHB

11-bit identifier

6 bytes user data

0x380 (896d) +
node ID

LLB

LHB

HLB

HHB

Содержание MC 5004






















































Результаты поиска

Содержание MC 5004

Отзывы:

Faulhaber MC 5004, Руководство по связи, Страница: 19 / 53

Результаты поиска

Содержание MC 5004

Отзывы: