Farmet EXCELENT PREMIUM 6 Скачать руководство пользователя | Manualshive

Страница: 17 / 52

background image

Manual

EXCELENT Premium 6; 8

17

│

52

Picture 16 – Turning on lifting/lowering

5.

Release the pressure oil so that the machine is fully lifted and the piston rods of the edge sections are

pushed out.

Picture 17 – Lifting the side sections of the rear rolls

6.

Open the cocks of the ball valves of the piston rods for lifting the central section.

Picture 18 – Ball valve of the axle and side frames

CLOSED

Picture 19 – Ball valve of the axle and side frames

OPEN

3.5.2

Folding the Machine

When folding the machine, progress in a reversed way:

1.

Lift the machine fully and close the cocks of the ball valves of the axle, see Picture 18.

2.

Turn off the function lifting/lowering on the display and turn on the function unfolding/folding, see Picture 20.

Picture 20 – Unfolding/folding on

Lifting / lowering

Unfolding / folding

«
...
15
16
17
18
19
...
»

Содержание EXCELENT PREMIUM 6





















































Отзывы:

Нет отзывов

Похожие инструкции для EXCELENT PREMIUM 6

Бренд: Zetec Страницы: 23

WJHD309A - DIGITAL DISK RECORDER

Бренд: Panasonic Страницы: 79

Бренд: Quincy lab Страницы: 4

Бренд: Bante Instruments Страницы: 6

Бренд: Haag-Streit Страницы: 18

Бренд: Haag-Streit Страницы: 20

Бренд: V-TEK Страницы: 2

Бренд: V-TEK Страницы: 112

Бренд: jablotron Страницы: 2

i-Digits Access

Бренд: Össur Страницы: 231

Бренд: PARAMOUNT BED Страницы: 120

BOMAG BVP 12/50 A

Бренд: Fayat Страницы: 105

HALO miniLUME LA5300

Бренд: Cooper Lighting Страницы: 2

Бренд: Free The Tone Страницы: 8

Бренд: Perel Страницы: 26

Бренд: Land Pride Страницы: 72

Evo TM/TSV2 Awning Wall Set

Бренд: Zempire Страницы: 2

Бренд: GERATHERM Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды