Farmet EXCELENT PREMIUM 6 Скачать руководство пользователя | Manualshive

Страница: 36 / 52

background image

Manual

EXCELENT Premium 6; 8

36

│

52

When you set the speed to zero, execute trial sowing for the relevant turnstile by pressing the red button on the
turnstile engine picture 52 and holding it until the bag has filled up by about 1/2. Generally, the larger the sowing
is, the more exact the trial is. When you release the button, the number of used revolutions will appear on the
display. Do not adjust this value.

Picture 52 – Button for the engine

P 53 H

When pressing the engine button, do not put your fingers or approach the gearing of the turnstile – there
is a danger of injury.

When the bag is full, take it off the diffuser and weigh it. Enter the result into the unit. Press the button for the
weight of trial sowing and adjust by pressing plus or minus to the required range. A red line will appear below
the number to indicate editing. Leave the menu by pressing the button again.
For faster editing, it is possible to press the button for the key after pressing plus or minus and the weight will be
adjusted automatically. You can stop the adjustment by pressing plus or minus again.

Picture 53 – Entering the weight

Perform the aforementioned for both sowing mechanisms separately. When you finish the weighing and entering
data into the unit, leave display 3 by pressing down the button with the cross. Finish the calibration of the sowing
batch on the main display. Press the button for setting the batch and adjust by pressing plus or minus to the
required range. A red line will appear below the number to indicate editing. Leave the menu by pressing the
button again. The sowing batch is now set.

Picture 54 – Adjustment of the sowing

When you open display 3 and then go back to the basic display, the sowing batch will be recalculated according
to the weighed value and turnstile revolutions. Therefore you have to adjust the required value.

«
...
34
35
36
37
38
...
»

Содержание EXCELENT PREMIUM 6





















































Отзывы:

Нет отзывов

Похожие инструкции для EXCELENT PREMIUM 6

Бренд: Canta Страницы: 2

Бренд: KaVo Страницы: 13

Бренд: vc999 Страницы: 52

Бренд: Keiser Страницы: 2

Бренд: ECA Страницы: 3

Бренд: Nautilus Страницы: 12

Бренд: Raymarine Страницы: 90

Бренд: ParaBody Страницы: 6

Бренд: Sailmon Страницы: 10

Бренд: B&W Tek Страницы: 12

Бренд: b&o Страницы: 46

Бренд: Taylor Страницы: 41

Бренд: Yanmar Страницы: 49

Бренд: Fagor Страницы: 12

Бренд: Baltic Страницы: 68

Бренд: H&S Страницы: 76

Бренд: Vaisala Страницы: 2

Бренд: Hammer Strength Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды