Fantic Motor INTEGRA 140 TRAIL Скачать руководство пользователя страница 86

Страница: 86 / 94

8-2

Ed. 1 - 11/2017

Troubleshooting

2. ERROR CODES

Check whether the error code that appears on the display is included in the table and, if so, proceed as indi-

cated.

Pay attention to the error codes!

The error codes can denote severe anomalies in the pedelec system. These

anomalies prevent a safe functioning of the pedelec and could cause damag-

es to the system itself or personal injuries. Stop using the pedelec.

Identify the meaning of the error code and please follow the indications in

order to correct it.

If you’re not sure of the meaning of the error code, please stop using the sys-

tem and park the bicycle. Please contact the manufacturer, the retailer or its

workshop to find information on how to proceed.

Problem

Possible cause

Possible solution

Battery pack charge level insufficient.

Recharge the battery pack using the dedi-

cated battery charger.

Battery charge level too high.

Turn the system off completely and turn it

back on using the button

on the Control

Panel. If the problem persists, please contact

the dealer or the retailer.

The battery is almost / completely dead.

Recharge the battery pack using the dedi-

cated battery charger.

Electrical measurements defective.

Turn the system off completely and turn it

back on using the button

on the Control

Panel. If the problem persists, please contact

the dealer or the retailer.

Heat sensor defective.

Turn the system off completely and turn it

back on using the button

on the Control

Panel. If the problem persists, please contact

the dealer or the retailer.

The internal voltage is outside the operat-

ing range.

Recharge the battery pack using the dedi-

cated battery charger.

>>>

Problem

Possible cause

Possible solution

The display indicates an error

code.

A system error is present.

Consult the following table.

Содержание INTEGRA 140 TRAIL































































































Результаты поиска

Содержание INTEGRA 140 TRAIL

Отзывы:

Бренды по названию

Популярные бренды

Fantic Motor INTEGRA 140 TRAIL, Руководство пользователя и по обслуживанию

Результаты поиска

Содержание INTEGRA 140 TRAIL

Отзывы:

Бренды по названию

Популярные бренды