background image

30

This window shows you a lot of different information and gives possibilities to 

test the currently used hardware and settings but also can be used for manual 

calibration:
On the upper left side there is a checkbox named ‘Enable auto calibration mode’ 

as shown on the right hand side 

(Note: This checkbox is shown on driver 

page ‘settings’ if CSL Elite Pedals LC are 

connected to wheel base):

This checkbox is deactivated per default when auto calibration mode is active 

or  after  updating  the  CSL  Elite  Pedals  LC  firmware. Activate  this  checkbox 

manually to enable the manual calibration mode (indicated in driver window: 

The buttons right above and below each pedal indicator bar are displayed only 

when manual calibration mode is active after a moment). See chapter ‘Pedal 

manual calibration’ of this manual for more details about the calibration process 

itself.
On the lower left side you can see the indi-

cator bars for each single pedal and for the 

ClubSport Handbrake, see picture on right 

hand side: 
When pressing a pedal of the CSL Elite Ped-

als the corresponding bar shows the signal 

level as a blue indicator, depending on the 

mechanical travel and on the manually cal-

ibrated minimum and maximum positions. 

Same with the ClubSport Handbrake if con-

nected to the CSL Elite Pedals LC.
Above every single indicator bar there are buttons ‘set max’, below every single 

indicator bar there are buttons ‘set min’. These buttons are only available when 

checkbox ‘Enable manual mode’ was activated by user before to enter manual 

calibration mode:

• 

When pressing a ‘set max’ button the current mechanical position of the 

corresponding pedal or the handbrake will be stored as the maximum 

position for this pedal or handbrake axis.

• 

When pressing a ‘set min’ button the current mechanical position of the 

corresponding pedal or the handbrake will be stored as the minimum 

position for this pedal or handbrake axis.

• 

See more detailed description in chapter ‘Pedal manual calibration’ of this 

manual.

Содержание CSL Elite Pedals
















































Отзывы: