background image

 

 

G3840/G3840F FRYERS

 

INSTALLATION, SERVICING 
and USER INSTRUCTIONS

 

 

 

These appliances must be installed and serviced by a qualified person as stipulated by the Gas Safety

 

(Installation & Use) Regulations.

 

IMPORTANT

 

The installer must ensure that the installation of the appliance is in conformity with these instructions 

and National Regulations in force at the time of installation. Particular attention MUST be paid to -

 

Gas  Safety  (Installation  &  Use)  Regulations  I.E.E.  Regulations  for  Electrical  Installations 

Health And Safety At Work etc. Act                        Electricity at Work Regulations

 

Local and National Building Regulations 

Fire Precautions Act

 

Detailed  recommendations  are  contained  in  DW172  Institute  of  Gas  Engineers  published 

documents : IGE/ UP/ 1, IGE/ UP/ 2IGE/ UP/ 4BS6173 and BS5440

 

These appliances have been CE-marked on the basis of compliance with the Gas Appliance Directive 

for the Countries, Gas Types and Pressures as stated on the data plate.

 

WARNING -

 

TO PREVENT SHOCKS, ALL APPLIANCES, GAS OR ELECTRIC, MUST BE EARTHED.

 

On  completion  of  the  installation,  these  instructions  should  be  left  with  the  Engineer-in-Charge  for 

reference during servicing. Further to this, the user instructions should be handed over to the user, 

having had a demonstration of the operation and cleaning of the appliance.

 

PREVENTATIVE MAINTENANCE CONTRACT

 

In  order  to  obtain  maximum  performance  from  this  unit  we  would  recommend  that  a  Maintenance 

Contract be arranged with SERVICELINE. Visits may then be made at agreed intervals to carry out 

adjustments  and  repairs.  A  quotation  will  be  given  upon  request  to  the  SERVICELINE  contact 

numbers below.

 

WEEE Directive Registration No. WEE/DC0059TT/PRO

 

At  end  of  unit  life,  dispose  of  appliance  and  any  replacement  parts  in  a  safe  manner, 

via a licenced waste handler. Units are designed to be dismantled easily and recycling of 

all material is encouraged whenever practicable.

 

 

This equipment is ONLY FOR PROFESSIONAL USE, and shall be operated by QUALIFIED persons. 

It  is  the  responsibility  of  the  supervisor  or  equivalent  to  ensure  that  users  wear  SUITABLE 

PROTECTIVE CLOTHING and to draw attention to the fact that some parts will, by necessity,  become 

VERY HOT and will cause burns if touched accidentally.

 

 
 

Falcon Foodservice Equipment

 

HEAD OFFICE AND WORKS

 

Wallace View, Hillfoots Road, Stirling. FK9 5PY. Scotland.

 

SERVICELINE CONTACT

 

Phone: 01438 363 000 

Fax: 01438 369 900

 

T100806 Ref. 6

 

Содержание G3840


















Отзывы: