Falcon E3840 Скачать руководство пользователя страница 9

1.0  INSTALLATION 

UNLESS OTHERWISE STATED, PARTS WHICH HAVE BEEN PROTECTED BY THE 
MANUFACTURER ARE NOT TO BE ADJUSTED BY THE INSTALLER. 

Please ensure that any plastic coatings are removed prior to use. Before operation, the pan 
requires to be thoroughly cleaned and dried. 
Discolouration of heated parts is caused by factory testing to ensure a satisfactory unit. It 
does not affect quality or performance. 

1.1 

MODEL NUMBERS, NETT WEIGHTS and DIMENSIONS

 

Model 

Width (mm) 

Depth (mm) 

Height (mm) 

Weight (kg) 

E3840 

400 

800 

880 

66 

E3840X 

400 

800 

880 

68 

E3840F 

400 

800 

880 

77 

E3840FX 

400 

800 

880 

79 

Pan oil capacity: 20 litres cold, good quality oil (to 

–MIN- mark) 

1.2 

SITING

 

The unit must be installed on a firm level floor in a well-lit draught free position. The fryer 
should not be installed in a position where the possibility of sideways tipping is likely when 
force is applied.  The means of restraint may be the manner of installation, such as 
connection to a battery of appliances or installing the fryer in an alcove, or by separate 
means, such as adequate ties. 

1.2.1 Anti-tipping Bracket 

An  anti-tipping  mechanism  is  available  as  an  accessory.  If  fitted,  the  brackets  must  be 
installed to locate the fryer in the correct position relative to any walls as detailed below. Fixing 
holes  are  provided  in  fryer  base  to  accommodate  the  bracket.  Details  of  fitting  can  be 
found in Figure 1 below. 
Attach  securely  to  fixing  point  and  secure  bracket  to  floor  after  alignment  with  bracket 
attached to the fryer. Adjust bracket to slide below floor bracket. 

Figure 1 - Anti-tipping Bracket 

Содержание E3840






































Отзывы: