Falcon E3840 Скачать руководство пользователя страница 24

20 

Warning 

When draining solids/shortening, ensure oil has time to strain through strainer 
basket. Heavily unfiltered oil may  overflow. 

Note 

This could cause pump to block over a period of time and is considered as misuse of equipment. 

7.1 

STARTING THE FILTRATION PROCESS

 

1.

Turn unit off at ON/OFF switch and allow oil to cool below 170°C (or if cold, heat to

minimum temperature of 60°C). P ull filter bucket forward.

2.

Ensure bucket is clean and emptied of all oil and debris. Refer to Section 8 for details of
how to clean filter components.

3.

Ensure strainer and microfilter are clean and dry.

4.

With strainer and microfilter in position, slide bucket back on to runner cradle and back

into fryer to engage with pump.

Please Note 

– Warning 

Do  not  handle  filter  components  or  adjacent  surfaces  when pump is operating. 
Components  will  remain  hot  for  a  period  after  filter.  Allow cooling. Use of PPE's is 
recommended.

 

7.1.1  E3840F, E3840FX. 

Note

: With the cabinet door open, filter pump switch is in centre of control panel (Refer to Figure 4). 

1.

Ensure appliance pan on/off switch is in OFF position.

2.

Allow oil to cool for approximately 15 - 20 minutes.

3.

Position bucket and filters and ensure these are clean and  dry.

4.

Open drain valve.

5.

Allow oil to drain from pan.

6.

Remove element guard from pan.

7.

Raise elements with the aid of the element lifting tool.

Please note: Elements and guard will still be hot! 

8.

Remove any frying debris from pan.

9.

If pan becomes blocked, clear using drain prod.

10.

Lower elements.

11.

Activate oil pump by means of filter pump switch to return oil to  pan.

12.

Leave to cycle for a few minutes before closing drain valve.

Warning 

When  pumping  solids/shortening  back  into  fryer  pan.  Ensure  all  trace  of 
solids/shortening  is  emptied  from  receptacle (bucket)

If oil is not emptied on a regular basis or if oil is left in the  receptacle, it may solidify 
and overflow or spill on to the  kitchen floor to create a hazard. 

Содержание E3840






































Отзывы: