Fagor 8025 GP, Руководство по эксплуатации

Страница: 100 / 423

105 This error comes up in the following cases:
> A comment has more than 43 characters.
> A program has been defined with more than 5 characters.
> A block number has more than 4 characters.
> Strange characters in memory.
106 ** Inside temperature limit exceeded.
107 ** Error in W axis leadscrew error compensation parameters. The CNC resets the serial line RS232C machine
parameters: "P0= 9600", "P1=8", P2=0", "P3=1", "P607(3)=1", "P607(4)=1", "P607(5)=1".
108 ** Error in Z axis leadscrew error compensation parameters. The CNC resets the serial line RS232C machine
parameters: "P0= 9600", "P1=8", P2=0", "P3=1", "P607(3)=1", "P607(4)=1", "P607(5)=1".
109 ** Error in Y axis leadscrew error compensation parameters. The CNC resets the serial line RS232C machine
parameters: "P0= 9600", "P1=8", P2=0", "P3=1", "P607(3)=1", "P607(4)=1", "P607(5)=1".
110 ** Error in X axis leadscrew error compensation parameters. The CNC resets the serial line RS232C machine
parameters: "P0= 9600", "P1=8", P2=0", "P3=1", "P607(3)=1", "P607(4)=1", "P607(5)=1".
111 * FAGOR LAN line error. Hardware installed incorrectly.
112 * FAGOR LAN error. It comes up in the following instances:
> When the configuration of the LAN nodes is incorrect.
> The LAN configuration has been changed. One of the nodes is no longer present (active).
When this error occurs, access the LAN mode, editing or monitoring, before executing a program block.
113 * FAGOR LAN error. A node is not ready to work in the LAN. For example:
> The PLC64 program is not compiled.
>A G52 type block has been sent to an 82CNC while it was in execution.
114 * FAGOR LAN error. An incorrect command has been sent out to a node.
115 * Watch-dog error in the periodic module.
This error occurs when the periodic module takes longer than 5 milliseconds.
116 * Watch-dog error in the main module.
This error occurs when the main module takes longer than half the time indicated in machine parameter "P741".
117 * The internal CNC information requested by activating marks M1901 thru M1949 is not available.
118 * An attempt has been made to modify an unavailable internal CNC variable by means of marks M1950 thru
M1964.
119 Error when writing machine parameters, the decoded M function table and the leadscrew error compensation
tables into the EEPROM memory.
This error may occur when after locking the machine parameters, the decoded M function table and the
leadscrew error compensation tables, one tries to save this information into the EEPROM memory.
120 Checksum error when recovering (restoring) the machine parameters, the decoded M function table and
leadscrew error compensation tables from the EEPROM memory.
150 Incoherent data in the 512 Kb memory.
When this error occurs, save as many programs as you can into the Floppy Disk Unit, peripheral or PC.
Then, proceed as follows to format the 512 Kb memory (when doing this, all part-programs stored in this
memory will be lost).
Press [OP MODE] [6] to select the Editing mode.
Press [LOCK/UNLOCK] the screen displays the text: CODE:
Key in: FM512 and press [ENTER]
Once the 512 Kb memory is formatted, recover (restore) the programs you saved into the Floppy Disk Unit,
peripheral or PC.