FAAC E024S, Руководство пользователя

Страница: 12 / 18

E024S 12 732642 - Rev. F
a
10 MM
16 MM
16 MM
8.3.1 REMOTE MEMORY STORAGE OF RC/LC RADIO
CONTROLS
Other radio controls can be remotely stored only with the RC/LC
radio controls, i.e. without using the LOGIC-SPEED-SETUP push-
buttons, but using a previously stored radio control.
1. Get a radio control already stored on one of the 2 channels
(OPEN A or OPEN B).
2. Press and hold down push-buttons P1 and P2 simultaneously
until both the LEDs flash slowly for 5 sec.
3. Within 5 sec. press the push-button of the radio control that had
been memory stored to enable learning on the selected
channel.
system is free of any obstacle created by
persons or things.
To add other radio controls, transfer the code of the
memory-stored push-button of the radio control to the relevant
push-button of the radio controls to be added, observing the
following procedure.
• On the memory stored radio control, simultaneously press
and hold down push-buttons P1 and P2.
• The radio control LED begins to flash.
• Release both push-buttons.
• Press the memory stored push-button and hold it down
(the radio control LED lights up on steady beam).
• Bring the radio controls near, press and hold down the
push-button of the radio control to be added, releasing
it only after the double flash of the radio control LED,
which indicates memory storage executed.
• Quickly press twice the push-button of the memory stored
radio control.
The automated system performs one opening
operation. Make sure that the automated
system is free of any obstacle created by
persons or things.
8.3 MEMORY STORAGE OF RC/LC RADIO CONTROLS
A maximum of 250 codes can be memory
stored, split between OPEN A and OPEN B.
1. Use RC/LC remote controls only with receiver module at 433
MHz.
2. Press the LOGIC (SW3) or SPEED (SW2) push-button, to memory
store respectively total opening (OPEN A) or partial opening
(OPEN B), and as you hold it down, also press the SETUP (SW1)
push-button. The relevant LED starts to flash slowly for 5 sec.
3. Release both push-buttons. Within these 5 sec., press the
appropriate push-button on the RC or LC remote control.
4. The LED lights up on steady beam for 1 second, indicating
memory storage executed, and then resumes flashing for
another 5 sec., during which another radio control (point
4) can be memory stored.
5. When the 5 sec. have elapsed, the LED goes OFF indicating
the end of the procedure.
6. To add other radio controls, repeat the operation at point 1.
4. The LED on the board relating to the channel being learned
flashes for 5 sec., within which time the code of another
radio control must be transmitted.
5. The LED lights up on steady beam for 2 seconds, indicating
memory storage executed, and then resumes flashing for
5 sec., during which other radio controls can be memory
stored, and then goes OFF.
8.4 RADIO CONTROLS DELETION PROCEDURE
1. To delete ALL the input radio control codes, press push-button
LOGIC (SW3) or SPEED (SW2) and, while holding it down, also
press push-button SETUP (SW1) for 10 sec.
2. The LED relating to the pressed push-button flashes for the first
5 sec, and then flashes more quickly for the next 5 sec.
3. Both LEDs light up on steady beam for 2 sec and then go OFF
( deletion completed).
4. Release both push-buttons.
This operation is NOT reversible. All codes of
radio controls stored as OPEN A and OPEN B will
be deleted.
9 BATTERY KIT OF E024S (OPTIONAL)
The buffer battery kit was built for insertion inside the control
board support.
This support (Fig.4 ref.
a
) was pre-moulded to permit the
battery housing to be opened.
1. Remove the board support material covering the
battery housing, cutting the material connections along
the perimeter.
2. Insert the battery in the housing you have just created, and
secure it on the anchoring supports (Fig.5).
3. To correctly fasten and connect the control unit to the J11 con -
nector, refer to the instructions enclosed with the battery kit.
Fig. 4
Fig. 5
ENGLISH