E024S
10
732642 - Rev. F
7.1
SETTING THE BUS PHOTOCELLS
Important to give both the transmitter and the
receiver the same address.
Make sure that there are not two or more pairs
of photocells with the same address.
If no BUS accessory is used, leave the BUS con-
nector free (J10 - fig. 1).
PAIR
Dip1
Dip2
Dip3 Dip4
Ref.
Type
1
OFF
OFF
OFF
OFF
B -C
OPENING
2
OFF
OFF
OFF
ON
3
OFF
OFF
ON
OFF
4
OFF
OFF
ON
ON
5
OFF
ON
ON
OFF
6
OFF
ON
ON
ON
7
ON
OFF
OFF
OFF
D
CLOSING
8
ON
OFF
OFF
ON
9
ON
OFF
ON
OFF
10
ON
OFF
ON
ON
11
ON
ON
OFF
OFF
12
ON
ON
OFF
ON
13
ON
ON
ON
OFF
14
OFF
ON
OFF
OFF
A
OPENING
and CLOSING
15
OFF
ON
OFF
ON
16
ON
ON
ON
ON
/
OPEN PULSE
Tab. 3 - Setting of bus photocells
Table 3 shows the programming operations of the dip-switch
inside the transmitter and of the BUS Photocells receiver.
A maximum of 16 BUS photocell pairs can be connected to
the board.
The photocells are split into groups:
Opening photocells:
max 6
Closing photocells:
max 7
Opening /Closing photocells:
max 2
Photocell used as an OPEN pulse:
max 1
Fig. 2 shows a 2-swing leaf automated system indicating the
coverage beams of the photocells:
A: Photocells with OPENING and CLOSING action.
B: Photocells with OPENING action
C: Photocells with OPENING action
D: Photocells with CLOSING action
6.3.5 RETURN TO DEFAULT SETTINGS
Restore the default settings as follows:
1. Keep the SETUP push-button pressed to switch the board ON.
2. Both SETUP LEDs are alternately lit
3. The board resets the parameters.
4. Until the SETUP push-button is pressed, movements are inhibited.
5. When the SETUP push-button is released, both LD4 and LD5
LEDs flash.
6. The default configuration is reset and the new Setup can be
started.
Fig. 2
6.3.6 PARAMETER DEFINITION
-
Anti-wind
: the anti wind function enables the gate to operate
even if there are gusts of wind. The obstacle detection time is
set to 5 s and commands the reversal of motion.
-
Reversing stroke:
when the gate is closed, the reversing stroke
function makes it possible that before the opening movement,
the motors push to close for approx. 3 s to facilitate uncoupling
the electric lock.
-
Soft-touch
: the soft touch function makes it possible that, after
touching the closing limit stop, the leaves reverse and then
rest gently. This function can be useful to observe the impact
curve as requested by current standards.
-
Pre-flashing:
it activates approx. 3 s before every opening
and closing movement
-
Leaf delay at opening:
it delays the leaf 2 start at opening
with respect to leaf 1, avoiding thus any interference between
the leaves.
-
Leaf delay at closure:
it delays leaf 1 at closure with respect
to leaf 2.
-
Pause time
: In logic A it is the time set for the leaf re-closure
after the opening.
- Stop point search space:
this parameter adjusts the
mechanical stop search angle within which the board stops
the movement without reversing if an obstacle is encountered
or the mechanical stop itself can be adjusted.
7
INSTALLATION OF BUS ACCESSORIES
This board is supplied with a BUS circuit enabling easy con
-
nection of a high number of BUS accessories (e.g. up to 16
photocells pairs), appropriately programmed, using only two
cable without polarity.
Below we describe the addressing and memory storage of
the BUS photocells.
For other future accessories, refer to the specific instructions.
ENGLISH
Содержание E024S
Страница 1: ...E024S...
