![background image](http://html1.mh-extra.com/html/faac/724mps/724mps_manual_535489006.webp)
11
ENGLISH
ENGLISH
5.
TECHNICAL SPECIFICATIONS
Supply voltage of transformer
230V~ (+ 6 % - 10 %) 50Hz
Supply voltage of control unit
22V~ (+ 6 % - 10 %) 50Hz
Power consumption
3 W
Motor max. load
70 W
Accessories max. load
24Vdc 500mA
Flashlight max. load
24Vdc 15W max
Ambient temperature
-20 ÷ +55 °C
Fuse
2
Function logics
Automatic / Stepped
Opening / closing time
Through self-learning at installation
Pause time
Through self-learning at installation
Thrust force
Two levels selected by Dip-switch
Deceleration
At opening and closing through self-learning
Terminal board inputs
Encoder / 22V~ Power supply / Battery power supply
Total opening / Opening for pedestrians / Stop / Photocells
Quick connector
For decoding - RP receivers card
Terminal board outputs
24 Vdc accessories power supply / 24Vdc Motor
24 Vdc Flashlight
Card dimensions
150 x 130 mm
Characteristics of toroidal transformer
prim. 230V~ sec. 22V~ / 150VA / dimens. Ø 105 x 40 mm
Characteristics of optional batteries
12V 4.5Ah / dimensioni 90 x 70 x 108 mm
Characteristics of outdoor container
305 x 225 x 125 mm - IP55
6.
INSTRUCTIONS
WARNING: To ensure people's safety, all warnings and instructions in
this booklet must be carefully observed. Incorrect installation or use
of the product could cause serious harm to people.
Make sure there is an adequate differential switch upstream of the
system as specified by current laws, and install a thermal breaker with
all-pole switch on the electrical mains.
To lay electrical cables, use adequate rigid and/or flexible tubes.
Always separate connection cables of low voltage accessories from
those operating at 230 V~.
To prevent any interference whatever, use separate sheaths.
In the version with control unit installed on the gearmotor, some
connections and units described in these instructions (motor,
transformer, encoder, etc) are factory prewired.
In the version with control unit housed in the watertight outdoor use
container, maximum length of connection cables between control unit
and motor/encoder must not exceed 3 m., using 2x2.5mm² cables for
the motor and 3x0.5mm² cables for the encoder.
Procedure (referring to fig. 13) for securing components in the watertight
container:
1) Secure the support of the toroidal transformer in position
A
by fitting
three Ø3.9x6.5 self-tapping screws (supplied) in the guides of the
watertight container.
N.B.: the support is sized to house a
transformer with characteristics and
dimensions specified in the table in
paragraph 5.
2) Secure the transformer on the support with
2 clamps (supplied).
3) If using floating batteries, secure the
relevant support in position
B
by fitting four
Ø3.9x6.5 self-tapping screws (supplied) in
the crossover holes of the guides of the
watertight container.
N.B.: the support is sized to house two
batteries (not supplied) with characteristics
and dimensions specified in the table in paragraph 5.
4) Position the batteries on the support.
5) Secure the control unit in position
C
by fitting four Ø3.9x6.5 self-
tapping screws (supplied) in the guides of the watertight container.
Procedure for securing the encoder on the
gearmotor (fig. 14) :
1) Using the four M4x10 screws
C
(supplied),
secure card
B
on cover
A
, locating the
spacers
D
between cover and card.
2) Using the M4x30 screw
F
(supplied), secure
encoder
E
directly on the thread on the
rotor of the gearmotor.
3) Wire up terminal board
G
as described
below.
7.
CONNECTIONS
7.1
TERMINAL BOARD M1
22V~ Power supply
Terminals “1-2”. This is the input to which the
secondar y winding of the transformer,
powered at 22 V~ 50Hz, should be
connected. When power is supplied by the
transformer, this is signalled by the POWER LED lighting up.
Batteries
Terminals “3-4”. The control unit is designed to operate with two floating
batteries (optional item) with minimum characteristics as indicated
on the table in paragraph 5.
When powered, the control unit keeps the batteries charged. The
batteries begin to operate when the transformer no longer supplies
power.
N.B.: power supplied by batteries should be considered an emergency
situation – the minimum number of gate operations is about 10/15.
In any event, the number of possible operations depends on the quality
of the batteries, structure of gate, and time elapsing since mains power
failed, etc, etc..
N.B.: observe the power polarity of the batteries
Accessories
Terminals “5-6”. Output for powering external accessories (24 Vdc).
N.B.: maximum load of accessories is 500 mA.
7.2
TERMINAL BOARD M2
Gearmotor
Terminals “7-8”. Connect the motor to the power supply of 24Vdc 70W
max.
Flashlight
Terminals “9-10”. Use a flashlight with fixed light operating voltage of
24Vdc 15W max. We advise you to connect it before programming,
as it indicates programming stages.
On opening, it pre-flashes steadily for 0.5 seconds, and for 1.5 seconds
at closing.
If the automatic logic is on, when the gate reaches the opening gate
stop, the flashlight stays on for 5 sec to inform the user it will re-close
automatically.
When the gate is open, the flashlight is off, and only flashes when the
safety devices are in use.
If the devices are in use for a long time, flashing only lasts 10 sec.
7.3
TERMINAL BOARD M3
Encoder
Terminals “11-12-13”. Use the encoder supplied with the control unit.
Connect the return signal from encoder terminal “11” to terminal “11”,
connect encoder terminals “12-13” to terminals “12-13”.
NB.: the control unit will not operate without an encoder.
NB.: observe the encoder's cable terminals.
Open-A
Terminals “14-18”. Any device (e.g. push-button, remote control, etc.)
can be connected to this circuit.
By closing a contact, the circuit generates a pulse for total opening
and/or closing of the gate. Its operating mode is set by dip-switch 3 –
see paragraph 9.
N.B.: a OPEN-A pulse during the pedestrian stage always has priority
over that stage
N.B.: to install several pulse generators, connect the contacts in parallel.
Open-B (For pedestrian use)
Terminals “15-18”. Any device (e.g. push-button, remote control, etc.)
can be connected to this circuit.
Fig. 13
Fig. 14