F.F. Group BPS 25/40 PLUS, Оригинальное руководство пользователя

Страница: 13 / 84

BPS 25/40V PLUS
www.ffgroup-tools.com
English | 13
PRODUCT SPECIFICATIONS
INTENDED USE
The machine is intended for domestic use, for pruning
trees and shrubs at elevated height, while the user is
situated on the ground. The machine is not intended
to cut inorganic material or to be used on a ladder or
steps. This tool is not intended for commercial or in -
dustrial use.
TECHNICAL DATA
Article Number 42 407
Model BPS 25/40 PLUS
Motor Brushless
Rated voltage V 36 (40max)
No load speed rpm 4.800-5.280
Chain speed m/s 9,5
Blade length cm 25
Max Reach m 3
Run Time min 20
No load running time min 56
Oil reservoir capacity ml 80
Weight kg 3,7
Chain bar Model (100SDEA041) 25 cm
Saw chain model (91P040X) 3/8’’ - 1,3 mm
Battery model
(not included)
BLi 40V/5.0Ah
Charger model
(not included)
CH 40V/2A
Sound emission values determined according to
EN 60745-1
Typically the A-weighted noise levels of the product are:
Sound pressure level dB(A) 76,3
Sound power level dB(A) 92,0
Uncertainty K dB 2,5
Vibration total values a
h
(triax vector sum)
and uncertainty K determined according to EN
60745-1
Vibration level max:
a
h ,HD
m/s 2 1,542
K m/s 2 1,5
IDENTIFICATION
1. Battery slot
2. Safety switch
3. Trigger
4. Pole
5. Telescoping release clasp
6. Angle adjustment button
7. Motor housing
8. Chain-tensioning ring
9. Cover Release Knob
10. Oil tank cover
11. Guide Bar
12. Saw Chain
13. Chain guard
14. Harness
PREPARING FOR USE
DANGER! To avoid serious personal injury, do not
operate the chainsaw without the chain bar, saw
chain, and side cover properly assembled.
WARNING: Do not attempt to operate the chain-
saw if any part is damaged or missing.
FILLING THE BAR AND CHAIN OIL RESERVOIR
IMPORTANT! Bar and chain oil prevents premature
wear. Never operate the chainsaw if oil is not vis-
ible in the inspection window. Check oil level fre-
quently and fill as needed.
f
Bar and chain oil is required to properly lubricate the
chain bar and saw chain. The chainsaw is equipped
with an automatic oiler that deposits oil on the bar
and chain when running, keeping them properly
lubricated. It is specially designed to provide low
friction and faster cuts. NEVER use oil or other lu-
bricants that have not been specifically designed for
use on the bar and chain. This can lead to a clogged
oil system which may cause premature wear of the
bar and chain.
f
Place the chainsaw on a firm, flat surface so that the
oil cap (10) is on top.
ƒ
Clean any debris from the cap area.
ƒ
Remove the cap (10) .
ƒ
Carefully pour the bar and chain oil into the res-
ervoir.
ƒ
Replace the cap and make sure oil is visible in the
reservoir.
TENSIONING THE SAW CHAIN
WARNING: If the chain is still loose when the saw
is at maximum tension, replace the chain.
IMPORTANT! Only tension the saw chain when
the chain is cool. A hot chain may contract and
damage the chain bar or chain as it cools.
Wear gloves.
ƒ
Remove the battery before tensioning.
ƒ
Loosen the side cover release knob (9) slightly,
but do not remove the side cover.
ƒ
Hold up the nose of the chain bar (E) and turn
the chain tensioning ring (8) clockwise.
ƒ
Tighten the chain tensioning ring until the low-
est cutters underneath the bar solidly contact
the bar.
ƒ
Tighten the side cover release knob.
ƒ
Lightly pull on the chain. The tension is correct